background image

SMCCO10-Z CO Alarm User Guide  

 

 

Copyright 

©

2013 SMC Networks

  

Page 15

 

 

All Rights Reserved 

I/M SMCC010-Z rev. 1.0 

1/23/2013 

9/3/10 

 

 

periods between cycles). 
 
Negative pressure differential resulting 
from the use of exhaust fans. 
 
Simultaneous operation of several fuel 
burning appliances competing for limited 
internal air. 
 
Vent pipe connection vibrating loose from 
clothes dryers, furnaces, or water 
heaters. 
 
Obstructions in or unconventional vent 
pipe designs which amplify the above 
situations

 

Extended operation of unvented fuel 
burning devices (range, oven, fireplace, 
etc.). 

 

Temperature inversions that can trap 
exhaust gasses near the ground. 

 

Car idling in an open or closed attached 
garage, or near a home. 

What CO Alarms Can and Cannot Do 

CO alarms provide early warning of the 
presence of CO, usually before a healthy adult 
would experience symptoms. This early 
warning is only possible if your CO alarm is 
mounted, installed, and maintained as 
described in this user manual. 

Because CO is a cumulative poison, symptoms 
can be caused by long-term exposures to low 
levels or short-term exposures to high levels. 
Your SMCCO10-Z has a time-weighted alarm; 
the higher the level of CO present, the sooner 
the alarm is triggered. 

Your SMCCO10-Z can only warn you about the 
presence of CO. It does not prevent CO from 
occurring and cannot solve existing CO 
problems. If your SMCCO10-Z has alarmed and 
you provided ventilation by leaving your 
windows and doors open, the CO buildup may 
have dissipated by the time help responds. 
Although your problem may appear to be 
temporarily solved, it is crucial that the source 
of the CO be determined and appropriate 
repairs made. 

CO alarm have limitation. Like any other 
electronic device, CO alarms are not fool-
proof. CO alarms have a limited operational 
life. You must test your CO alarm weekly, 
because it could fail to operate at any time. 

If your CO alarm fails to test properly, or if its 
self-diagnostic test reveals a malfunction, 
replace the unit immediately. Your SMCCO10-Z 
will not monitor CO levels while in an trouble 
condition. 

CO alarm can only sense CO that reaches the 
unit’s sensor. It is possible that CO may be 
present in other areas without reaching the 
alarm. The rate and ability with which CO 
reaches the alarm may be affected by: 

 

Doors or other obstructions. 

 

Fresh air from a vent, an open window, 
or other source. 

 

CO being present on one level of the 
home and not reaching a CO alarm 
installed on a different level. (For 
example, CO in the basement may not 
reach an alarm on the second level, near 
the bedrooms). 

Summary of Contents for SMCCO10-Z


















Reviews: