background image

SMCCO10-Z CO Alarm User Guide 

 

Copyright 

©

2013 SMC Networks

  

Page 10 

 

All Rights Reserved 

I/M SMCC010-Z rev. 1.0 

1/23/2013 

9/3/10 

 

 

B.

 

Perform steps A through D in Step 6, 
“Adding to the Touchscreen” on 
page 3. 

C.

 

At the Technician Settings menu, 
select 

Sensors & Zones > Delete a 

Sensor/Zone

. The Premise 

Passphrase keyboard appears. 

D.

 

Enter the Premise Passphrase and 
click 

Done

. The currently installed 

sensors/security zones appear. 

E.

 

Tap the zone you want to delete 
and follow the instructions on the 
Touchscreen to delete the 
SMCCO10-Z and security zone from 
the current system. 

11  

 

Troubleshooting 

SMCCO10-Z does not power up 
properly or reports low battery 

 

Be sure the batteries are fully 
seated within the battery 

compartment and the polarity is 
correct. 

 

Check the battery voltage (1.5 VDC 
nominal per battery). 

Touchscreen does not respond 

 

Use a wireless RF sniffer to confirm 
that the SMCCO10-Z is sending 
messages for activation. 

 

Be sure the SMCCO10-Z is enrolled 
into the Touchscreen properly. 

 

Be sure you are using a compatible 
Touchscreen (see “Specifications” 
on page 11). 

Tamper condition does not restore 

 

Be sure the SMCCO10-Z is installed 
on the mounting plate properly and 
the mounting plate has a magnet. 

 

Be sure there are no trouble 
indications at the CO alarm. 

 

Be sure you are using a compatible 
Touchscreen (see “Specifications” 
on page 11). 

If a tamper alarm occurs 

 

Be sure you are using a compatible 
Touchscreen (see “Specifications” 
on page 11). 

 

Be sure the Touchscreen is in sensor 
test mode during sensor testing. 

Alarm/open condition does not restore 

 

Be sure the smoke or heat has 
cleared the SMCCO10-Z. 

 

Be sure you are using a compatible 
Touchscreen (see “Specifications” 
on page 11).

Summary of Contents for SMCCO10-Z


















Reviews: