manualshive.com logo in svg

SMC Networks LEC-GPR1 Series, Operation Manual

Share
Download
SMC Networks LEC-GPR1 Series Operation Manual Download Page 22

- 21 - 

 

 

4. 4 SIEMENS PLC S7 Connection Method 

 

Below is an explanation of the LEC-GPR1 connection method with a SIEMENS PLX STEP7

TM

. 

 
4.4.1 GSD File Installation 

After STEP7TM has been stated. 
Open[Hardware Configuration] screen. 
Select “Opton-Install New GSD” From the mwnu var. 
Select GSD File, and click the Open button. 
After completiong the above steps,” Anybus-CC PROFIBUS DP-V1”will automatically be added to the 

Hardware Catalog under the STE7TM[PROFIBUS DP][Additional Field Device][General]Folder. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

* Screen data used on this document is taken for STEP7TM software by Siemens AG. 

 
4.4.2 Adding Stations 

Drag and drop “Anybus-CC PROFIBUS DP-V1”from the Hardware Catalogue to the station window. 

[Properties-PROFIBUS interface”dialogue box will be displayed. 

Enter the unit address on the dialogue boz.Please make sure that the address entered is the same as 

the address set, using the switches. 

Pree the OK button to confirm the address setting. “Anybus-CC PROFIBUS DP-V1”will be shown on 

the station window. 
 
 
 
 
 
 
 
 
 

Summary of Contents for LEC-GPR1 Series




























































Reviews:

No comments

Brands by name

Popular brands

Load more brands