background image

IDX-OM-X011 

Chapter 1

 

Safety

 

1.2

 Hazard Classifications & Position of Hazard warning Labels 

IDF190D/240D Series 

 
 

1-2 

1.2  Hazard Classifications & Position of Hazard 

warning Labels 

To ensure the safety of the operators, potential hazards are classified and marked with warning labels. 
Confirm the potential hazards and positions of the labels before operation. 

 

 

 

 

 

 

 

 

 

1.2.1 

Hazard of Electricity   

 

 

 

 

 
1.2.2 

Hazard of Hot Surface   

 

 

 

 

 

1.2.3 

Hazard of Rotating Object 

 

 

 

 

 

1.2.4 

Hazard of Compressed Air Circuit 

 

 

 

 

 

 

 

 

- Transportation, installation, and maintenance involve risks and should only be carried out by 

people who have sufficient knowledge and experience about the product and its accessories. 

- If there is abnormality, take actions below according to the operation manual. 

- Read carefully the Chapter 6 Troubleshooting before taking actions. 

- Do not start the product in any trouble. If failure occurs, immediately stop the product, and 

contact maintenance personnel or a qualified person. 

The product has surfaces that can reach high temperatures during operation. What is more,   
there is also the danger of burn injury due to remaining heat after the power supply is cut.   
Therefore, wait until the temperature of hot parts become 50

o

C and below. 

WARNING 

Before replacing or cleaning parts, be sure to bleed compressed air remaining inside of the   
product until the gauge indicates “0”. If there is no relief to the pressure, high pressure can   
propel objects at high velocity when unscrewing parts and cause injury. 

WARNING 

WARNING 

Inside of this product, there is a power-supplying section with high voltage separated by the 
cover panel. Do not operate the product without the cover panel. 

WARNING 

Since this product has parts that rotate during operation, there is the danger of burn injury 
resulting from contact with them. Though sometimes those parts can temporarily stop the 
rotation, they will rotate again, and so do not work with them while running mode. 

WARNING 

Summary of Contents for IDF190D Series















































Reviews: