background image

IDX-OM-X011 

Chapter 3

 

Transportation and installation

 

3.2

 Installation 

IDF190D/240D Series 

 
 

3-4 

3.2.4 

Replacement of auto drain 

 

Mount the nipple to the auto drain (included in the same package). Then connect it to the drain inlet of the dryer.

 

 

Connect the drain piping to the auto drain outlet. The drain piping should have an internal diameter of 8mm or 
more and be 5m or less in length. Make sure that it does not go upwards and it is not bent. The outlet end of the 
tube is released to atmosphere, and lets the drain flow through the tube.

 

  Ensure that the ball valve is opened. Refer to 7.3 Dimensions of the Chapter 7. 

  Using the pressure of the compressed air, the drain will be discharged periodically. Fix the outlet end 

of the tube so as not to swing during discharge. 

 

 

 

 

 

 

 

3.2.5 

Electrical wiring 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 

3.2.5.1. 

Wiring of the power supply cable 

  Remove the front panel of the product and connect the power cable to the terminal block. 

  Install the earth leakage breaker on the power supply side. It needs to be prepared by the user. 

  Allowable power supply fluctuation:     

3 phase    200 VAC +/-10% (50Hz); 3 phase 200 VAC to 220V +/-10% (60Hz) 
3 phase with different voltage (IDF190 / 240D-9-



): AC220V, 240V, 380V, 400V, 415V, 440V+/-10% 

 

Power supply cable specification 

Prepare the power supply cables below. 

Power supply cable: 10AWG (5.5mm

2

 or greater), cable O.D. Approx. 16mm, 4 cores (including the 

ground) 

Approx. 1.5m of cable is necessary for wiring in the product. 

 

All  electrical work must be carried out in a  safe  manner by  a qualified person in compliance 
with applicable national regulations. 

Be sure to shut off the user’s power supply. Wiring with the product energized is strictly 

prohibited. 

- Ensure a stable power supply with no surge. 
- Install the correct electric earth leakage breaker of the specified leakage capacity and load 

capacity referring to 7.1 Specifications to prevent electric shock and burning of the 
compressor motor. 

- Use a power supply suitable for the specifications of the product. 

3 phase power supply type cannot be operated by single phase power supply.   

- Be sure to connect the ground connection. 
- Never connect the ground to water line, gas pipe or lightning conductor. 
- Do not plug too many leads into a single socket. That causes exothermic heat or fire.   
- Do not modify the internal electrical wiring of the product. 
- For use in Europe, install a breaker compliant with applicable IEC standards to the power 

supply of the product.

 

WARNING 

- During drain work, follow the procedure that you define to keep the safety of worker. (ex. 

Put on protective glass, apron, and gloves). 

- In case that oil gets mixed in the wasted water that is discharged from the auto drain, the 

waste liquid treatment is necessary. Handle it following the bylaw or regulation of local 
government. 

 

WARNING 

Summary of Contents for IDF190D Series















































Reviews: