Smartgen HGM9120 User Manual Download Page 16

Page: 16 / 58

HGM9120 Genset Controller

HGM9120 Genset Controller Version: 1.0 2014-04-14 Page 16 of 58

4.3.2 PARAMETERS SETTING MENU

Parameter setting Including as following,

★

Mains settings

★

Timer settings

★

Engine settings

★

Generator settings

★

Load settings

★

Switch settings

★

Analog sensor settings

★

Input port settings

★

Output port settings

★

Module settings

★

Scheduling and maintenance settings

★

GSM settings

Example,

Advanced Parameters

>Mains Setting
>Timer Setting
>Engine Setting

Form1: Use

to scroll settings,

to enter

settings (Form 2),

to exit settings menu.

>Generator Setting

Generator
> Return

Form 2:

Use

to scroll settings (Form 3); Select

” Return”

and press

back to previous menu(Form 1)

back

to previous menu.(Form 1 )

> AC System

> Poles
> Rated Voltage

Generator
>Under voltage shutdown
>Over freq shutdown
>Under freq shutdown

Form 3:

Use

to scroll settings.

confirm setting (Form

4),

back to previous menu (Form 1).

>Over voltage warn

Summary of Contents for HGM9120



























































Search results

Summary of Contents for HGM9120

Reviews:

Related manuals for HGM9120

Brands by name

Popular brands

Smartgen HGM9120, User Manual

Search results

Summary of Contents for HGM9120

Reviews:

Related manuals for HGM9120

Brands by name

Popular brands