background image

                           

HGM8156 GENSET PARALLEL CONTROLLER USER MANUAL 

HGM8156 Genset Parallel (With Mains) Controller            2019-09-10        Version 1.1          Page 42 of 44

 

13 

INSTALLATION 

Controller is panel built-in design and it is fixed by clips when installed. The controller overall dimensions 

and cutout size are as below:   

 

Fig. 10 Case Dimensions and Cutout   

13.1 BATTERY VOLTAGE INPUT 

HGM8156  controller  suits  wide  range  battery  voltage  (8~35)VDC.  Negative  of  battery  must  be 

connected with the shell of starter. The wire diameter of connecting B+ and B- with battery negative and 

positive must not be less than 2.5mm

2

. If floating charger is installed, please firstly connect output wires 

of  charger  to  battery’s  positive  and  negative  directly,  then  connect  wires  from  battery’s  positive  and 

negative to controller power input terminals in order to prevent charger 

disturbing the controller’s normal 

working.     

13.2 OUTPUT AND EXPAND RELAYS 

CAUTION!

 All outputs of controller are relay contact outputs. If it needs to expand relays, please add freewheel diode 

to both ends of expansion relay coils (when coils of relay has DC current) or, increase resistance-capacitance return 

circuit (when coils of relay has AC current), in order to prevent disturbance to controller or other equipments. 

13.3 AC INPUT 

Current input must be connected to outside current transformer.  Curren

t transformer’s secondary side 

current must be 5A. At the same time, phases of current transformer and input voltage must be correct, 

otherwise collected current and active power may not be correct.   

NOTE:

 ICOM port must be connected to negative of battery.

 

WARNING! 

When there is load current, transformer’s secondary side is prohibitted to open circuit.

 

13.4 WITHSTAND VOLTAGE TEST 

CAUTION! 

When  controller  has  been  installed  in  control  panel,  if  high  voltage  test  is  needed,  please  disconnect 

controller’s all terminal connections, in order to prevent high voltage entering controller and damaging it. 

Summary of Contents for HGM8156













































Reviews: