background image

                           

HGM8156 GENSET PARALLEL CONTROLLER USER MANUAL 

HGM8156 Genset Parallel (With Mains) Controller            2019-09-10        Version 1.1          Page 15 of 44

 

MULTI-CHANNEL MAINS OPERATION 

In multi-channel mains system, multiple gensets are controlled by HGM8156 and they supply multiple 

load. If something abnormal occurs for one mains channel, controller will control genset to start and take 

load. If something abnormal occurs for multiple channels, controller will control genset to take load one 

by one. When there is only one mains channel normal, controller will control switch and make mains take 

the load. When there are multiple mains channels normal, controller will control mains to take the load 

one by one.   

HGM8156 priority includes status priority and module priority. When status priorities are different, priority 

is  decided  by  status.  When  status  priorities  are  the  same,  the  priority  is  decided  by  module  priority. 

Module priority can be set by users, but status priority cannot.   

Table 7 Status Priority 

Status Priority 

Conditions 

High 

 

Low 

Auto mode, mains failure, bus unloading 

Auto mode, mains recover 

Auto mode, mains failure, bus loading 

Auto mode, mains normal, request to control gensets 

Manual mode, gensets ready to run, or are running 

Auto mode, mains normal 

Manual mode, gensets not start 

Stop mode 

Summary of Contents for HGM8156













































Reviews: