SMA SUNNY TRIPOWER 10.0 Operating Manual Download Page 14

Page: 14 / 106

3 Scope of Delivery

SMA Solar Technology AG

Operating manual

STP8-10-3AV-40-BE-en-12

Scope of Delivery

Check the scope of delivery for completeness and any externally visible damage. Contact your
distributor if the scope of delivery is incomplete or damaged.

Figure 1: Components included in the scope of delivery

Position

Quantity

Designation

Inverter

Wall mounting bracket

Pan head screw M5x12

Positive DC connector

Negative DC connector

Sealing plug

AC connector

RJ45 protective sleeve: swivel nut, cable support sleeve, threaded
sleeve

WLAN antenna

Quick reference guide with password label on the rear side
The label contains the following information:

• PIC (Product Identification Code) identification key for

registering the system in Sunny Portal

• RID (Registration Identifier) registration ID for registering the

system in Sunny Portal

• WLAN password WPA2-PSK (WiFi Protected Access 2 -

Preshared Key) for direct connection to the inverter via WLAN

Summary of Contents for SUNNY TRIPOWER 10.0











































































































Search results

Summary of Contents for SUNNY TRIPOWER 10.0

Reviews:

Related manuals for SUNNY TRIPOWER 10.0

Brands by name

Popular brands

SMA SUNNY TRIPOWER 10.0, Operating Manual

Search results

Summary of Contents for SUNNY TRIPOWER 10.0

Reviews:

Related manuals for SUNNY TRIPOWER 10.0

Brands by name

Popular brands