SMA SUNNY TRIPOWER 10.0 Operating Manual Download Page 96

Page: 96 / 106

12 Decommissioning the Inverter

SMA Solar Technology AG

Operating manual

STP8-10-3AV-40-BE-en-12

12. If there is a protective cap available, plug the

protective cap onto the jack for connecting the
antenna.

13. If an additional grounding or an equipotential

bonding is connected to the inverter, unscrew the
pan head screw M5x12 (TX25) and remove the
grounding cable.

14. Unscrew the left- and right-hand pan head screws

M5x12 used to secure the inverter to the wall
mounting bracket (TX25).

15. Remove the inverter by lifting it vertically up and off

the wall mounting bracket.

16. Unscrew the screws for fastening the wall mounting

bracket and remove the wall mounting bracket.

17. If the inverter is to be stored or shipped, pack the inverter, the AC connector, the DC

connector, the RJ45 protective sleeve, the antenna and the wall mounting bracket. Use the
original packaging or packaging that is suitable for the weight and dimensions of the inverter.

18. Dispose of the inverter in accordance with the locally applicable disposal regulations for

electronic waste.

Summary of Contents for SUNNY TRIPOWER 10.0











































































































Search results

Summary of Contents for SUNNY TRIPOWER 10.0

Reviews:

Related manuals for SUNNY TRIPOWER 10.0

Brands by name

Popular brands

SMA SUNNY TRIPOWER 10.0, Operating Manual

Search results

Summary of Contents for SUNNY TRIPOWER 10.0

Reviews:

Related manuals for SUNNY TRIPOWER 10.0

Brands by name

Popular brands