Skyworks Si5332-AM1 Reference Manual Download Page 4 | Manualshive

Page: 4 / 63

background image

2. Power Supply Sequencing

The Si5332 VDD_core voltages are VDD_DIG, VDD_XTAL, and VDDA. These 3 VDD_core pins must all use the

same

voltage. Power

supply sequencing between VDD_core and any VDDOx pin is allowed in any order. However, if desiring to minimize the “bring-up” time,
it is recommended that VDD_core is powered up first; this ensures that the NVM download is completed first and the I

2

C master can

communicate with the Si5332 slave. The figure below shows the Si5332 device power-up sequencing and expected device behavior.
Note that a blank (unconfigured) part will stop and wait to be configured with outputs disabled.

Outputs available and

stable

Time (system time delay)

for PLL clock

Time (system time delay)

for Oscillator startup/

Time (system time delay)

for input clock availability

Program Si5332 volatile

memory with a frequency

plan

Time (system time delay)

for NVM download

Power supplies for

VDDA, VDD_DIG, and

VDD_XTAL stable

Is this a blank part?

Figure 2.1. Power Supply Sequencing for Si5332

Si5332-AM1/2/3 Automotive Grade Device Reference Manual • Power Supply Sequencing

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com

4

Rev. 0.3 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 26, 2021

4

«
...
2
3
4
5
6
...
»

Summary of Contents for Si5332-AM1
































































Reviews:

No comments

Related manuals for Si5332-AM1

Brand: Hama Pages: 4

Brand: Hama Pages: 2

Brand: Hama Pages: 4

Brand: Hama Pages: 39

Brand: Denver Pages: 13

Brand: Majestic Pages: 26

Brand: i-box Pages: 60

Brand: Bellman Pages: 4

Brand: ATS Pages: 7

Brand: Imperial Pages: 56

Brand: EBENCH Pages: 8

Brand: OttLite Pages: 53

Brand: Epson Pages: 47

Brand: G-project Pages: 20

Brand: Seg Pages: 29

Brand: Techno Line Pages: 16

Brand: La Crosse Pages: 2

Brand: La Crosse Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands