Skyworks Si5332-AM1 Reference Manual Download

Page: 38 / 63

Register Field Name

Address

Base

Bit

Length

R/W/RW

Description

Device Mode

ID0A_INTG

The terms of an a + b/c desired divider set-
ting must be processed into ID0A_INTG,

ID0A_RES, and ID0A_DEN register terms.
INTG = floor(((a*c+b)*128/c) - 512).

READY if divider

is currently driving

the output, else,

READY/ACTIVE

ID0A_RES

res = mod(b*128, c)

ID0A_DEN

den = c

ID0A_SS_ENA

Spread spectrum enable. This is the on-
ly bank configuration field which may be
changed dynamically while the bank is se-
lected as the active bank. Users may freely
enable/disable spread spectrum.

0 = spread spectrum disabled

1 = spread spectrum enabled

READY if divider

is currently driving

the output, else,

READY/ACTIVE

ID0A_SS_MODE

Spread spectrum mode.

0 = disabled

1 = center

2 = invalid

3 = down

ID0A_SS_STEP_NUM

Number of frequency steps in one quarter
SSC modulation period, allows for frequen-
cy step every output clock.

ID0A_SS_STEP_INTG

Divide ratio spread step size.

ID0A_SS_STEP_RES

Numerator of spread step size error term.

Si5332-AM1/2/3 Automotive Grade Device Reference Manual • Si5332 Common Registers

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com

Rev. 0.3 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 26, 2021

Summary of Contents for Si5332-AM1
































































Search results

Summary of Contents for Si5332-AM1

Reviews:

Related manuals for Si5332-AM1

Brands by name

Popular brands

Skyworks Si5332-AM1, Reference Manual

Search results

Summary of Contents for Si5332-AM1

Reviews:

Related manuals for Si5332-AM1

Brands by name

Popular brands