manualshive.com logo in svg

sitrex Action 120, Use And Maintenance Manual

Share
Download
sitrex Action 120 Use And Maintenance Manual Download Page 27

  

Round Baler ACTION 120 

USE AND MAINTENANCE MANUAL                                   - 27 - 

 

Pic. 12A 

– Electric signal M50 

5.8  ELECTRIC SWITCH-BOARD 

“M100” (OPTIONAL)  

The  whole  cycle  for  binding  is  managed  by  an 
electric  switch-board  with  the  following  functions 
(Pic. 12B): 

1-  BUTTON FOR SELECTING TWINE OR 

NET 

2-  BUTTON STARTING BINDER 
3-  STOP LIGHT FULL CHAMBER 
4-  FEEDING LIGHT SWITCH BOARD 

 

 

Pic. 12B 

– Electric switch-board M100 

5.9  AUTOMATIC SWITCH-BOARD 

“M200” (OPTIONAL) 

5.9.1 Installation and linkage 

The  control  device  has  to  be  installed  inside  the 
tractor and has to be fed by cable. That cable has 
to  be  protected  by  a  20A  fuse,  which  will  be 
directly  connected  with  the  tractor  battery  (code 
nr. 53006910). 
Both  the  delivery  connectors  have  to  be 
connected with baler. 

 WARNING 

If  the  control  device  will  be  fed  with  inverted 
polarity,  it  won’t  be  possible  to  switch  it  on 
and display will keep switched off. 

5.9.2 Control description 

 

Pic. 12C 

– Automatic switch-board M200 

The switch-board 

“M200” has the following 

functions (Pic. 12C): 

1-   MULTIFUNCTION DISPLAY 

On the left-hand side it display selected 
binder: 

 = twine 
 = net 

On the centre it display working procedure: 
MAN = Manual 
S-AT = Semi-automatic 
AUTO = Automatic 
On the right-hand side it display bales 
counter (total or partial) 

 
2-   LED STOP 
 
3-   SWITCH ON/OFF 
 
4-   COUNTER KEY 

It alternate the total counter display with the 
display of 4 partial counters (A, B, C, D). 

 

To set at zero the displayed partial 

counter press the key for 4 seconds. 

 
5-   START KEY 
 
6-   MODE KEY 

It select working procedure. 
During the navigation in MENU give the 
possibility to move on the left. 

 

Summary of Contents for Action 120













































Reviews:

No comments

Brands by name

Popular brands

Load more brands