Sitecom WLM-4601 User Manual Download Page 47 | Manualshive

Page: 47 / 71

background image

Enable Automatic firmware update

: When enabled the router will check for updates

on the firmware if an updated firmware has been released the router will inform you that
a newer firmware is available and offers to download and install the firmware.

This page also allows you to manually upgrade the firmware for the router. Click the
“Browse” button to select the firmware file and click the “Upgrade Firmware” button to
start upgrading.

IMPORTANT! Do not turn off your router while this procedure is in progress.

Reboot

Whenever you use the Web configuration to change system settings, the changes are
initially placed in temporary storage. To save your change for future use, you have to
click “Apply” to reboot the router. If you have encountered problems during the
configuration, you can click the “OPS” button in the top panel of the router over 15
seconds to reset default settings.

«
...
45
46
47
48
49
...
»

Summary of Contents for WLM-4601








































































Reviews:

No comments

Related manuals for WLM-4601

Brand: T-Mobile Pages: 8

Brand: T-Mobile Pages: 3

Brand: H3C Pages: 41

LigoPTP 5-23 UNITY

Brand: LogoWave Pages: 14

Brand: Hamlet Pages: 10

Brand: HPE Pages: 4

Brand: HPE Pages: 4

Altitude 4521 Series

Brand: Extreme Networks Pages: 64

Brand: BAZOO Pages: 2

Brand: Air Live Pages: 9

Hirschmann BAT-F Series

Brand: Belden Pages: 72

Hirschmann OpenBAT BAT-R

Brand: Belden Pages: 76

Brand: Yunlink Pages: 13

Brand: Vivato Pages: 181

Brand: Ijinus Pages: 9

Brand: Axis Pages: 60

Brand: Laird Pages: 40

Brand: RFNet Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands