Sitecom WLM-4601 User Manual Download | Manualshive

Page: 39 / 71

background image

When you finish, click „Submit‟ to save the settings made.

IP Filter Listing

#

: Item number.

Enable

: Whether the connection is currently active.

Src IP Mask

: The source IP address or range of packets to be monitored.

Dest IP Mask

: This is the destination subnet IP address.

Protocol

: It is the packet protocol type used by the application, select either TCP or UDP

or ICMP

Src port

: This Port or Port Ranges defines the port allowed to be used by the

Remote/WAN to connect to the application. Default is set from range 0 ~ 65535. It is
recommended that this option be configured by an advanced user.

Dest Port

: This is the Port or Port Ranges that defines the application.

«
...
37
38
39
40
41
...
»

Summary of Contents for WLM-4601








































































Reviews:

No comments

Related manuals for WLM-4601

Brand: D-Link Pages: 20

Brand: D-Link Pages: 95

DIR-450 - 3G Mobile Router Wireless

Brand: D-Link Pages: 79

Brand: Fortinet Pages: 31

Brand: Ubiquiti Pages: 17

Brand: Ubiquiti Pages: 13

Brand: Icidu Pages: 16

Brand: TP-Link Pages: 86

Brand: Arista Pages: 4

Brand: Arista Pages: 4

Brand: Harman Pages: 23

NUCLIAS CONNECT DAP-2680

Brand: D-Link Pages: 48

Brand: D-Link Pages: 24

Brand: D-Link Pages: 24

Brand: D-Link Pages: 24

Brand: D-Link Pages: 25

Brand: D-Link Pages: 26

nuclias connect DAP-2662

Brand: D-Link Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands