Sitecom WLM-4601 User Manual Download | Manualshive

Page: 53 / 71

background image

Connect & Disconnect

“NetUSB” allows you to use USB printers when they‟re actually connected to the Sitecom
USB server.

The “connect” operation is a software operation that simulates an actual USB device
plug-in. Therefore, when you do a “connect” operation in the Control Center, the PC can
detect a USB device‟s plug-in, although actually you do not plug in any USB device to
your PC. Similarly, the “disconnect” operation is a software operation that simulates the
disconnection of the USB device.

Note

: If a USB device is “connected” by a PC, we say that PC has the ownership of the

USB device. Only one PC can get the ownership of a USB device at the same time.

«
...
51
52
53
54
55
...
»

Summary of Contents for WLM-4601








































































Reviews:

No comments

Related manuals for WLM-4601

F5D7132 - Wireless G Universal Range Extender/Access Point

Brand: Belkin Pages: 2

Brand: Hama Pages: 67

Brand: FMN Pages: 28

Brand: AQL Pages: 3

Brand: Planet Pages: 37

Brand: Cerio Pages: 53

Brand: Cables to Go Pages: 63

Brand: ZyXEL Communications Pages: 2

Brand: Arista Pages: 14

Brand: EnGenius Pages: 2

Brand: Ubiquiti Pages: 15

Brand: Novatel Pages: 106

Brand: Skullcandy Pages: 31

PICOSTATION-M2-HP

Brand: Delta Pages: 5

Brand: Air Live Pages: 98

Brand: Air Live Pages: 103

Brand: TECOM Pages: 17

Brand: 4gon Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands