Sitecom WLM-4601 User Manual Download Page 54 | Manualshive

Page: 54 / 71

background image

NetUSB installation

The steps to do installation for USB devices, like MFPs:

Make sure the router is turned on.

Connect the USB device to the USB port of the router.

Run the Control Center. In the “USB MFP Server List” window, you can see
the host names and IP addresses all of the Sitecom servers (in blue) on the
network, as shown below.

Click the server. Then all USB devices attached to the server will be shown.

Please follow the user manual of the USB device to install its driver. For
example, you may put the driver CD of the USB device in the CD-ROM player
to install the driver.

When you are asked to plug in the USB device into PC‟s USB port, click the
desired USB device in the Control Center and then click the “Auto-Connect
Printer” button to do the connect operation and get the ownership of the USB
device. The computer name of the device owner will be shown at the end of
the device.

«
...
52
53
54
55
56
...
»

Summary of Contents for WLM-4601








































































Reviews:

No comments

Related manuals for WLM-4601

Brand: Dali Pages: 8

RouterBOARD 750

Brand: MikroTik Pages: 2

UniFi UAP-FlexHD

Brand: Ubiquiti Pages: 22

Brand: NETGEAR Pages: 2

Brand: iBall Baton Pages: 62

Brand: Minitar Pages: 77

Brand: Conrad Pages: 76

Brand: Ajoho Pages: 24

Brand: EnGenius Pages: 4

Brand: HomeMatic Pages: 23

Brand: HomeMatic Pages: 45

Brand: Spectrum 24 Pages: 142

Brand: Packedge Pages: 16

Brand: SafeTrust Pages: 2

Brand: Nexcom Pages: 82

Sport PRO AM66-L

Brand: honor Pages: 156

Brand: Draytek Pages: 1

Brand: Draytek Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands