SIP SILVERCUT DISC 300 TS FC, Instruction For Work

Page: 98 / 138

SILVERCUT
5
P.T.O. SHAFT drive (only for implements driven by
a P.T.O Shaft)
1.
Use only P.T.O. Shafts prescribed by the
manufacturer!
2. PTO shaft - protection tubes and protection pots,
driveshaft protection on the tractor, and on inlet
shaft on the machine must be on their places and
in good condition!
3. Take care about the prescribed P.T.O. Shaft tube
overlap in transport and working position!
4. P.T.O. Shaft can only be mounted when the P.T.O.
Shaft connection and engine are switched off and
the ignition key is pulled out!
5. When using the P.T.O. Shafts with overload and/or
free-wheel clutch, which are not covered by a
protection on the tractor, put the overload or the
free-wheel clutch on the machine side!
6. Always pay your best attention to proper mounting
and securing of the P.T.O. Shaft!
7. Secure the P.T.O. Shaft protection against rotating
by a chain!
8. Before switching on the P.T.O. Shaft make sure,
that the selected RPM and rotating direction of
the tractor connection match with the allowed
RPM and rotating direction of the machine!
9. When using two-way PTO shaft take into
consideration that RPM depend of driving speed
and rotation direction at reverse drive
Invert!
10. Make sure that nobody is in the area of danger of
the machine before switching on the P.T.O. Shaft!
11. Never switch on the P.T.O. Shaft when the engine is
switched off!
12. When working with the P.T.O. Shaft nobody is
allowed to be in the area of rotating P.T.O. Shaft.
13. Always switch off the P.T.O. Shaft when the angle
deviation gets too big or when you do not need it!
14. Attention! After having switched off the P.T.O.
Shaft the danger of rotating heavier parts
remains. Do not get close to the machine untill it
comes to a complete standstill. You can start to
work only when the rotation is completely
stopped.
15. Cleaning, lubrication or adjusting of the machines,
driven by the P.T.O. Shaft, or a P.T.O. Shaft itself,
can be done when the e engine is switched off and
the ignition key is pulled out!
16. Disconnected P.T.O. Shaft is to be put onto
provided holder!
17. When PTO Shaft pulled from the tractor, push the
protection cap back on the drive shaft of the
tractor!
18. Repair all damages of the P.T.O. Shaft before using
the machine!
Maintenance
1.
After mowing, clean the cutter bar. When using
high-pressure jet cleaners NOT direct in
bearings!
2. Maintenance, repairs, cleaning and disturbance
removing may only be executed when the drive
and the engine are switched off and the ignition
key is pulled out!
3. Check nuts and screws regularly to be sure that
they are tightened enough. If not tighten them!
4. If you perform any maintenance on the lifted
implement, always secure the implement by a
suitable holder.
5. Use adequate tools and gloves when replacing
machine parts with sharp edges!
6. Store properly oils and greases!
7. Before repairs on electrical equipment are
started, switch off the electrical current – remove
the fuse!
8. If safety devices succumb to usage, must be
checked regularly and replaced in duet ime!
9. When welding on the tractor or on machine which
is mounted on the tractor, disconnect the cable
from battery and from generator!
10. Use only genuine spare parts, they guarantee long
lifetime of the machine!
11. When filling in the gas, use for filling in exclusively
azote. Danger of EXPLOSION!
1. Foreword
SIP machines are equipped with all the necessary
safety elements. However, it is impossible to secure all
the dangerous locations on the machine and keep its
unrestricted functionality at the same time. The
machine is equipped with corresponding warnings
(yellow-black symbols) drawing attention to other
dangers.
See the following note for the position of those
symbols and their meaning:
Read carefully text of safety decals, check
on the machine where are they to be
found, because there are danger areas.