Simplicity AGCO Allis 400 Series, Service & Repair Manual

Page: 86 / 136

9-7
9 Hydro Transmission Repair
Hydro-Gear 310-0500
1 1 SPRING, Return
2 A/R WASHER, 3/4
3 1 SPRING
4 1 PULLEY, Idler
5 1 SPACER, 25/64 x 5/8 x 11/16
6 1 KLIPRING, 1/2
7 1 SPACER
8 1 PAD, Pedal
9 1 ROD, Clutch, Front
10 1 CLUTCH/BRAKE PEDAL
11 1 BELT GUARD
12 1 TORSION BAR
13 2 BRACKET, Torsion Bar
14 1 PIVOT, Brake
15 1 KLIP RING, 3/4
16 1 SPRING, Compression
17 1 ROD, Return, Front
18 1 ROD, Clutch, Rear
19 2 CLEVIS, Idler Bracket
20 1 PLATE
21 1 ROD, Control
22 1 ROD, Brake
23 1 LEVER, Control
24 1 SPACER
25 1 ROD, Shift, Front
26 1 PIVOT SHAFT ASSY.
27 1 ROD, Return, Rear
28 1 SPACER, Pivot
29 1 TUBE
30 2 LOCKWASHER, 5/16
31 1 LOCKWASHER, 5/16
32 2 NUT, Hex, 5/16-18
33 1 NUT, Hex, 5/16-18
34 6 COTTER PIN, 7/64 x 3/4
35 3 WASHER, Plain
36 1 WASHER, Plain
37 2 WASHER, Plain, 5/16
38 2 NUT, Hex, Lock, 5/16-18
39 1 CAPSCREW, 5/16-18 x 1-3/4
40 1 CAPSCREW, Hex, 1/4-20 x 3/4
41 2 WASHER, Plain, 1/2 x 1 x 1/32
42 1 WASHER, Plain
43 4 SCREW, Taptite, 5/16-18 x 1/2
44 1 WASHER, Plain, 13/32 x 7/8 x 5/64
45 1 SCREW, Taptite, 1/4-20 x 5/8
46 3 NUT, Hex, Flange Whiz, 1/4-20
47 1 CARRIAGE BOLT, 1/4-20 x 7/8
48 1 CARRIAGE BOLT, 5/16-18 x 1
49 1 CARRIAGE BOLT, 5/15-18 x 2-3/4
50 1 CARRIAGE BOLT, 3/8-16 x 2-/1/4
51 1 CARRIAGE BOLT, 5/16-18 X 1-1/4
52 1 NUT, Hex, Jam, Lock, 3/8-16
53 2 KEY
Ref. Qty. Description Ref. Qty. Description
Transmission Removal
1. Elevate the rear end. (See Elevating Rear End for
Safe Service) and remove the rear wheels. (See
Rear Wheel Removal).
2. Engage the parking brake and remove the drive belt
from the transmission input pulley.
3. Disengage the parking brake.
4. Remove the cotter pin (34, Figure 4) from the brake
rod (22) and remove the brake rod from the pivot
shaft assembly (26).
5. Remove the cotter pin (34, Figure 4) from the front
shift rod (17) and remove the shift rod from the pivot
shaft assembly (26).
6. Remove the return spring (2, Figure 3).
7. Disassemble the front and rear return rods (21 & 25,
Figure 4)
8. Disconnect the torque straps(9 & 15, Figure 3).
9. Place a jack under the transaxle. Remove the axle
mounting bolts from the left and right side of the carri-
er assembly. Lower the transmission out of the carri-
er assembly being careful not to damage any of the
linkages.