Sime 8112265 Operating, Installation And Servicing Instructions Download Page 22

Page: 22 / 56

8 INSTALLATION

CAUTION

The appliance must only be installed by the

Sime

Tech-

nical Service or by qualified professionals

who MUST

wear

suitable protective safety equipment.

8.1

Receiving the product

Brava Slim HE R

appliances are delivered in a single unit protect-

ed by cardboard packaging.

Open the cardboard packaging, with appropriate tool and pull

out the boiler.

Fig. 17

The plastic bag found inside the packaging contains the follow-

ing:

– Installation, use and maintenance manual

– Paper template for boiler installation

– Certificate of warranty

– Hydrostatic test certificate

– System booklet

– Bag with expansion plugs

IT IS FORBIDDEN

To leave packaging material around or near children

since it could be dangerous. Dispose of it as pre-

scribed by legislation in force.

8.2

Dimensions and weight

Fig. 18

Description

Brava Slim HE R

20 R i

20 R e

40 R i

40 R e

W (mm)

400

450

400

450

D (mm)

250

256

250

303

H (mm)

700

917

700

917

Weight (kg)

28.5

30.0

8.3

Handling

Once the packaging has been removed, the appliance is to be

handled manually, tilting it slightly, lifting it and applying pres-

sure in the points indicated in the figure.

Fig. 19

IT IS FORBIDDEN

To grip the appliance casing. Hold the "solid" parts of

the appliance such as the base and structural frame.

WARNING

Use suitable tools and accident protection when re-

moving the packaging and when handling the appli-

ance. Observe the maximum weight that can be lifted

per person.

8.4

Installation room

The room where the appliance is to be installed must comply

with the Technical Regulations and Legislation in force.

The minimum temperature of the installation room must NOT

be lower than

-5 °C

CAUTION

– Before assembling the appliance, the installer

MUST

make sure that the wall supports the weight.

– Remember to consider the space needed in order to

access the safety/adjustment devices and to carry

out maintenance interventions (see Fig. 20).

Summary of Contents for 8112265

























































Search results

Summary of Contents for 8112265

Reviews:

Related manuals for 8112265

Brands by name

Popular brands

Sime 8112265, Operating, Installation And Servicing Instructions

Search results

Summary of Contents for 8112265

Reviews:

Related manuals for 8112265

Brands by name

Popular brands