Sime 8112265 Operating, Installation And Servicing Instructions Download Page 24

Page: 24 / 56

CAUTION

The wall on which the appliance is to be hung must

be of adequate strength and capable of holding the

weight of the appliance and associated components

and pipework.

CAUTION

The height of the boiler is to be such that disassembly

and maintenance interventions are facilitated.

8.9

Plumbing connections

The plumbing connections have the following characteristics

and dimensions.

Brava Slim HE 20 R i

40 R i

212

130

400

Fig. 22

Brava Slim HE 20 R e

40 R e

130

450

175 (20 R e)

216 (40 R e)

Fig. 23

Description

Brava Slim HE R

20 R i

20 R e

40 R i

40 R e

M - System delivery

Ø 3/4" G

R - System return

Ø 3/4" G

G - Gas supply (*)

Ø 3/4" G

Sc - Condensate outlet

Ø 25 mm

F - Filling

Ø 1/2" G

(*) Brass adaptor for gas connection supplied. G3/4" to R3/4".

8.10

Condensate outlet/collection

In order to collect the condensate, it is recommended that:

– the appliance condensate outlets and the smoke outlet are

ducted

– a neutralising device is prearranged

– the outlet incline is

>3%

CAUTION

– The condensate outlet duct must be airtight, suita-

bly sized to that of the siphon and must not be re-

stricted at any point.

– The condensate outlet must be constructed in full

compliance of the National or Local regulations in

force.

– Before commissioning the appliance, fill the siphon

with water.

8.11

Gas supply

Brava Slim HE R

boilers leave the factory prearranged for gas

NATURAL GAS

and can also work with

Universal LPG

without the

need for any type of mechanical conversion. Select parame-

ter

"03"

(see “Parameter setting and display") and set the type

of gas to be used.

If changing the type of gas to be used, carry out the entire appli-

ance "Gas conversion" phase.

The boiler must be connected to the gas mains in full com-

pliance with the installation standards in force in the country

where the appliance will be used.

Before connecting the boiler to the gas mains, the user must

ensure that:

– the type of gas is correct for the appliance

– the pipes are clean

– the gas supply pipe is the same dimension as or greater than

that of the boiler fitting (G3/4") and with a load loss less than

or equal to that contemplated between the gas mains and the

boiler.

WARNING

Once installation has been completed, check that

the joints are air tight as indicated in the installation

Standards.

CAUTION

It is recommended that the gas line has a suitable fil-

ter.

Summary of Contents for 8112265

























































Search results

Summary of Contents for 8112265

Reviews:

Related manuals for 8112265

Brands by name

Popular brands

Sime 8112265, Operating, Installation And Servicing Instructions

Search results

Summary of Contents for 8112265

Reviews:

Related manuals for 8112265

Brands by name

Popular brands