Sime 8112265 Operating, Installation And Servicing Instructions Download Page 9

Page: 9 / 56

MAINTENANCE

3.1

Adjustments

For the appliance to operate correctly and efficiently it is recom-

mended that the User calls upon the services of a Professionally

Qualified Technician to carry out

BI-ANNUAL

maintenance.

CAUTION

Maintenance interventions must ONLY be carried out

by professionally qualified personnel who will follow

the indications authorised in the INSTALLATION AND

MAINTENANCE INSTRUCTIONS.

3.2

External cleaning

WARNING

– Should it be necessary to access the areas in the

bottom part of the appliance, make sure that the

system components and pipes are not hot (risk of

burning).

– Before performing any maintenance, put on protec-

tive gloves.

3.2.1

Cleaning the cladding

When cleaning the cladding, use a cloth dampened with soap

and water or alcohol for stubborn marks.

IT IS FORBIDDEN

to use abrasive products.

DISPOSAL

4.1

Disposal of the equipment (European Di-

rective 2012/19/EU)

At the end of their life span, the appliance

and electrical and electronic devices coming

from households or classifiable as household

waste must be delivered to appropriate waste

collection systems, in accordance with the law

and with Directive 2012/19/EU. This product

was designed and manufactured for minimis-

ing its impact on the environment and on hu-

man health, but it contains components that

could be detrimental if managed improperly.

The symbol (crossed-out wheelie bin) depict-

ed here and also appearing on your appliance

means that the appliance at the end of its life

must be managed in accordance with the law

and treated as electrical and electronic waste.

Before delivering the appliance for its disposal,

consult the applicable provisions of the laws in

force in the country where the appliance is used

and get information on the authorised waste

disposal facilities by contacting the relevant lo-

cal offices.

IT IS FORBIDDEN

dispose of the product with urban waste.

Summary of Contents for 8112265

























































Search results

Summary of Contents for 8112265

Reviews:

Related manuals for 8112265

Brands by name

Popular brands

Sime 8112265, Operating, Installation And Servicing Instructions

Search results

Summary of Contents for 8112265

Reviews:

Related manuals for 8112265

Brands by name

Popular brands