Sime 8058540, Manual

Page: 40 / 72

40
right side of the boiler body with the
screws (5).
– Hook the tie rod (6) to the seats extract-
ed from the front and rear grid.
– Place the intermediate grids (11).
– Introduce the ring (4) and the lever (3) on
the hub (9), fixing then everything with
the washer (2) and the screw (1).
1.2.5 ASSEMBLY OF THE
ACCESSORIES
The closing handles for the ports and the
screw with the adjustment knob for the
blast gate damper are supplied separately,
since they could be damaged during the
transport.
Both the handles and the screws with
knob are packed in a nylon bag, introduced
inside the ash collection basin.
For the assembly of the handles proceed as
following (fig. 4):
– Take a handle (1), insert it in the open-
ing of the load port (2) and introduce
the roll (3) in the opening of the handle;
block the handle introducing the elastic
split pin (4).
– Carry out the same operation for the
handle of the ash box port.
To assemble the screw with the knob, pro-
ceed as follows (fig. 5):
– Remove the screw M8 x 60, which fixes
the air blast damper to the ash box port
and screw the screw with the bakelite
knob (1) on, which is supplied in the
packaging.
Place the blind nut with cap (2) at the
end of screw M 10.
– Fix lever M6 to the air blast damper (3)
placing it in a horizontal direction on
the right. The lever has an opening at its
end, where the chainlet of the thermo-
static regulator will be connected.
1.2.6 CASING ASSEMBLY
Two superior tie rods are screwed on three
nuts at the front side of the boiler: the
second and the third nut serve to place cor-
rectly the lateral sides of the casing.
Two nuts one to fix the clamp holders
for the lateral sides are screwed on the
inferior tie rods, both from the front side
and from the rear side of the boiler. The
assembly of the casing components has to
be carried out in the following way (fig. 6):
– Unscrew with some rotations the sec-
ond or third nut of each tie rod.
– Hook the left side (1) on the lower tie
rod and superior of the boiler and adjust
the position of the nut and locknut of the
upper tie rod.
– Fix the lateral side in blocking the lock-
nut.
– In order to assembly the right side (2)
proceed in the same way.
– Hook the front upper board (3) intro-
ducing the two splines in the opening,
obtained on each side.
– Carry out the same operation to fix the
back lower board (4).
– The protection deflector (5) is fixed to
the control board (6) with three self-
threading screws.
Fix the board by means of the pressure
stakes.
Then unwind the capillary of the ther-
mometer and introduce it in the left
sheath of the posterior head, introducing
the contact spring.
The right sheath can be needed for the
check thermometer.
– Fix the cover (7) at the lateral sides of
the boiler.
NOTE: Keep the “Test certification”
together with the boiler documents in the
combustion chamber.
1.2.7 DRAUGHT REGULATOR
The boilers “SOLIDA PL” can assemble
indifferently 2 types of thermostatic regu-
lators.
NOTE: In order to fix the lever with the
chainlet in the regulator holder it is
necessary to remove the deflector in
aluminum, which is assembled on the
control board, by unscrewing the three
screws that fix it (fig. 6).
Replace the protection deflector after the
assembling and related adjustment.
“THERMOMAT RT-C” Regulator
The “Thermomat” regulator is equipped
with a thermosetting resin knob of an
adjustment field from 30 to 100 °C (fig. 7).
Screw the regulator on the 3/4” opening
of the anterior head and orientate the red
index on the upper part.
The lever with the chainlet should be intro-
duced in the regulator holder after having
assembled the instrument holder board
and after having removed the plastic lock.
If the joint is taken out, which fixes the
lever with the chainlet, take care in assem-
LEGEND
1 Handle
2 Load port
3 Roll
4 Elastic split pin
Fig. 4
LEGEND
1 Screw with knob M10 x 70
2 Blind nut with cap
3 Blast gate damper
LEGEND
1 Left side
2 Right side
3 Posterior superior board
4 Posterior inferior board
5 Protection deflector
6 Control board
7 Cover
Fig. 5
Fig. 6