background image

26

IQ Power HL Power Supply

5201258 Rev. C

Simco-Ion

2257 North Penn Road
Hatfield, PA 19440
 
(215) 822-6401
(800) 203-3419
www.simco-ion.com
[email protected]

© 2019 Simco-Ion.  Printed in the U.S.A.

9. WARRANTY & SERVICE

This product has been carefully tested at the factory and is warranted to be free from 

This product has been carefully tested at the factory and is warranted to be free 

from any defects in materials or workmanship. Simco-Ion will, under this warranty, 

repair or replace any equipment that proves, upon our examination, to have become 

defective within one year from the date of purchase. 
The equipment being returned under warranty should be shipped by the purchaser 

to Simco-Ion, 2257 North Penn Road, Hatfield, PA 19440, transportation prepaid 

and insured for its replacement cost. Prior to returning any goods for any reason, 

contact Simco-Ion Customer Service at (215) 822-6401 for a Return Authorization 

Number. This number must accompany all returned items. 
This warranty does not apply when the equipment has been tampered with, misused, 

improperly installed, altered, has received damage through abuse, carelessness, 

accident, connected to improper line voltage, or has been serviced anyone other than 

an authorized factory representative. 
The warranty does not apply when Simco-Ion parts and equipment have been 

energized by other than the appropriate Simco-Ion power supply or generator, 

or when a Simco- Ion power supply or generator has been used to energize other 

than Simco-Ion parts and equipment. Simco-Ion makes no warranty, expressed or 

implied, nor accepts any obligation, liabilities, or responsibility in connection with 

the use of this product other than the repair or replacement of parts stated herein. 
Information in this publication supersedes that in all previous published material. 
Specifications are subject to change without notice.

Summary of Contents for IQ Power HL





























Reviews: