Silverline 942944, User Manual

Page: 4 / 46

GB
Air Belt Sander 942944
4 5
silverlinetools.com
Original Instructions
WARNING:
Always wear ear protection where the sound level exceeds 85dB(A) and limit
the time of exposure if necessary. If sound levels are uncomfortable, even with ear protection,
stop using the tool immediately and check the ear protection is correctly fitted and provides
the correct level of sound attenuation for the level of sound produced by your tool.
WARNING:
User exposure to tool vibration can result in loss of sense of touch,
numbness, tingling and reduced ability to grip. Long term exposure can lead to a chronic
condition. If necessary, limit the length of time exposed to vibration and use anti-vibration
gloves. Do not operate the tool with hands below a normal comfortable temperature, as
vibration will have a greater effect. Use the figures provided in the specification relating to
vibration to calculate the duration and frequency of operating the tool.
Sound and vibration levels in the specification are determined according to international
standards. The figures represent normal use for the tool in normal working conditions. A poorly
maintained, incorrectly assembled, or misused tool, may produce increased levels of noise and
vibration. www.osha.europa.eu provides information on sound and vibration levels in the
workplace that may be useful to domestic users who use tools for long periods of time.
General Safety
a) For multiple hazards, read and understand the safety instructions before installing,
operating, repairing, maintaining, changing accessories on, or working near this tool.
Failure to do so can result in serious bodily injury
b) Only qualified and trained operators should install, adjust, or use this tool
c) Do not modify this tool. Modifications can reduce the effectiveness of safety measures and
increase the risks to the operator
d) Do not discard the safety instructions; give them to the operator
e) Do not use this tool if it has been damaged
f) Tools shall be inspected periodically to verify that the ratings and markings required by
this part of ISO 11148 are legibly marked on the tool. The employer/user should contact
the manufacturer to obtain replacement marking labels when necessary
WARNING:
This appliance is not intended for use by persons (including children) with
reduced, physical or mental capabilities or lack of experience or knowledge unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety. Children must be supervised to ensure that they do not play with
the appliance.
Projectile Hazards
a) Be aware that failure of the workpiece or accessories, or even of the inserted tool itself, can
generate high-velocity projectiles
b) Always wear impact-resistant eye protection during operation of this tool. The grade of
protection required should be assessed for each use
c) For overhead work, wear a safety helmet
d) The risks to others should also be assessed at this time
e) Ensure that the workpiece is securely fixed
Description of Symbols
The rating plate on your tool may show symbols. These represent important information about
the product or instructions on its use.
Wear hearing protection
Wear eye protection
Wear breathing protection
Wear head protection
Wear hand protection
Read instruction Manual
WARNING:
Moving parts can cause crush and cut injuries.
DO NOT use with compressed gas cylinders!
Caution!
Conforms to relevant legislation and safety standards
Environmental Protection
Air tools should not be disposed of with household waste. They contain traces
of oil and other lubricants. Please recycle where facilities exist. Check with your
local authority or retailer for recycling advice.
Specification
No load speed: ...................................................................................16,000min
-1
Belt:....................................................................................................10 x 330mm
Maximum operating pressure: ........................................................6.3Bar (90psi)
Air Consumption (CFM): ................................................................................4CFM
Inlet connection: .........................................................................................¼" BSP
Oil specification: .......................................................................Generic Air Tool Oil
Weight:
.......................................................................................................0.75kg
As part of our ongoing product development, specifications of
Silverline products may alter without notice.
Sound and vibration information:
Sound Pressure L
PA
: .................................................................................88.6dB(A)
Sound Power L
WA
: ....................................................................................99.6dB(A)
Uncertainty K: ...................................................................................................3dB
Vibration emission value a
h
: ...................................................................... 0.9m/s
2
Uncertainty K: ........................................................................................... .1.5m/s
2
The sound intensity level for the operator may exceed 85dB(A)
and sound protection measures are necessary.
n
o
No load speed
n
Rated speed
Nm
Newton metres (torque)
psi
Pounds per square inch
° Degrees
Ø
Diameter
W, kW Watt, kilowatt
/min or min
-1
Operations per minute
rpm
Revolutions per minute
BSP
British Standard Pipe (thread)
dB(A)
Decibel sound level (A weighted)
m/s
2
Metres per second squared
(vibration magnitude)
Technical Abbreviations Key
Introduction
Thank you for purchasing this Silverline tool. This manual contains information necessary for
safe and effective operation of this product. This product has unique features and, even if you
are familiar with similar products, it is necessary to read this manual carefully to ensure you fully
understand the instructions. Ensure all users of the tool read and fully understand this manual.
942944_Manual.indd 4 15/02/2017 08:42