background image

4

GB

Carefully read and understand this manual and any label attached to the tool 

before use. Keep these instructions with the product for future reference. Ensure 

all persons who use this product are fully acquainted with this manual.
Even when used as prescribed it is not possible to eliminate all residual risk 

factors. Use with caution. If you are at all unsure of the correct and safe manner in 

which to use this tool, do not attempt to use it.

General Power Tool Safety 

Warnings

WARNING Read all safety warnings and all instructions.

 

Failure to follow the 

warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded) 

power tool or battery-operated (cordless) power tool.

Work Area Safety

a) 

Keep work area clean and well lit.

 

Cluttered or dark areas invite accidents

b) 

Do not operate power tools in explosive atmospheres, such as in the 

presence of flammable liquids, gases or dust.

 

Power tools create sparks 

which may ignite the dust or fumes

c) 

Keep children and bystanders away while operating a power tool.

 

Distractions can cause you to lose control

Electrical Safety

a) 

Power tool plugs must match the outlet. Never modify the plug in any 

way. Do not use any adapter plugs with earthed (grounded) power 

tools.

 

Unmodified plugs and matching outlets will reduce risk of electric 

shock

b) 

Avoid body contact with earthed or grounded surfaces, such as pipes, 

radiators, ranges and refrigerators.

 

There is an increased risk of electric 

shock if your body is earthed or grounded

c) 

Do not expose power tools to rain or wet conditions. 

Water entering a 

power tool will increase the risk of electric shock

d) 

Do not abuse the cord. Never use the cord for carrying, pulling or 

unplugging the power tool. Keep cord away from heat, oil, sharp edges 

or moving parts.

 

Damaged or entangled cords increase the risk of electric 

shock

e) 

When operating a power tool outdoors, use an extension cord suitable 

for outdoor use.

 

Use of a cord suitable for outdoor use reduces the risk of 

electric shock

f) 

If operating a power tool in a damp location is unavoidable, use a 

residual current device (RCD) protected supply.

 

Use of an RCD reduces 

the risk of electric shock 

NOTE: 

The term “residual current device (RCD)” may be replaced by the 

term “ground fault circuit interrupter (GFCI)” or “earth leakage circuit breaker 

(ELCB)”.

Personal Safety

a) 

Stay alert, watch what you are doing and use common sense when 

operating a power tool. Do not use a power tool while you are tired 

or under the influence of drugs, alcohol or medication.

 

A moment of 

inattention while operating power tools may result in serious personal injury

b) 

Use personal protective equipment. Always wear eye protection.

 

Protective equipment such as dust mask, non-skid safety shoes, hard hat, 

or hearing protection used for appropriate conditions will reduce personal 

injuries

c) 

Prevent unintentional starting. Ensure the switch is in the off-position 

before connecting to power source and/or battery pack, picking up or 

carrying the tool. 

Carrying power tools with your finger on the switch or 

energising power tools that have the switch on invites accidents

d) 

Remove any adjusting key or wrench before turning the power tool on.

 

A wrench or a key left attached to a rotating part of the power tool may result 

in personal injury

e) 

Do not overreach. Keep proper footing and balance at all times.

 

This 

enables better control of the power tool in unexpected situations

f) 

Dress properly. Do not wear loose clothing or jewellery.

 

Keep your hair, 

clothing and gloves away from moving parts. Loose clothes, jewellery or long 

hair can be caught in moving parts

 

g) 

If devices are provided for the connection of dust extraction and 

collection facilities, ensure these are connected and properly used.

 

Use 

of dust collection can reduce dust-related hazards

Power Tool Use & Care

a) 

Do not force the power tool. Use the correct power tool for your 

application.

 

The correct power tool will do the job better and safer at the 

rate for which it was designed

Description of Symbols

The rating plate on your tool may show symbols. These represent important 
information about the product or instructions on its use. 

Wear hearing protection 
Wear eye protection 
Wear breathing protection
Wear head protection

 

Wear hand protection

 

Read instruction manual

 

Double insulated for additional protection

 
Conforms to relevant legislation and safety standards

Environmental Protection 

Waste electrical products should not be disposed of with 
household waste. Please recycle where facilities exist. Check 
with your local authority or retailer for recycling advice

 

Specification

 

 Voltage .............................................................230V~/50Hz
 Power ..............................................................1200W
  No load speed ..................................................600 – 3000min

-1

  Spindle thread ..................................................M14, male
  Backing Pad diameter ......................................180mm
  Weighted vibration ...........................................6.51m/s

2

 Uncertainty.......................................................1.5m/s

2

  Sound pressure ................................................84.1dB(A)
  Sound power ...................................................95.1dB(A)
 Uncertainty.................................................  .....3dB
 Weight .............................................................3.54kg
  Protection Class: ..............................................

As part of our ongoing product development, specifications of 

Silverline products may alter without notice.

The sound intensity level for the operator may exceed 85dB(A) and 

sound protection measures are necessary.

Sound and vibration levels in the specification are determined according to 

EN 60745. The figures given can be used to compare similar tools tested to 

this standard.  These figures may be used to assess exposure to noise and 

vibration levels.
The figures represent normal use for the tool in normal working condition. 

A poorly maintained, incorrectly assembled or mis-used tool may produce 

increased levels of noise and vibration.  The total working period that 

you can operate this tool must factor in periods where the tool is idle or 

switched off.  Allow frequent rest breaks when operating this tool.
It is in the interest of users to maximise their safety using the correct safety 

equipment like ear defenders that protect against loud or repetitive noise 

and anti-vibration gloves that minimise vibration.  Do not operate the tool 

with your hands below a normal comfortable temperature as vibration will 

have a greater effect.
www.osha.europa.eu provides information on sound and vibration levels in 

the workplace that may be useful to domestic users who use tools for long 

periods of time

264569_Z1MANPRO1.indd   4

04/03/2013   12:19

Summary of Contents for 264569





























Reviews: