www.silverlinetools.com
7
260W Oscillating Multi-Tool
243574
5. Before using the tool, check that the blade or scraper is securely fitted and
the bolt is tight
Note:
Blades or scrapers that are cranked or bent must be mounted on the tool so
that the end of the blade is away from the tool as shown in Fig. B.
Fitting the sanding pad and sanding sheets
1. Use the supplied hex key to loosen
and remove the Mounting Bolt (9)
and Mounting Washer (8), turning
the bolt anti-clockwise as you face
the Mounting Spindle (6) (see Fig. A)
2. Position the supplied sanding pad
on to the flange of the Mounting
Spindle (6), so that the mounting
holes in the Sanding Pad (10)
engage with the pins on the flange
(see Fig. C)
3. The Sanding Pad can be positioned
at an angle if required but normally
a point of the triangle base is
directly in line with the body of the
tool
4. Re-fit the Mounting Bolt and
Mounting Washer carefully, as
shown in Fig. B, ensuring the
Sanding Pad correctly sits in the
flange pins, as the bolt is tightened.
The sanding pad and Mounting
Spindle can be damaged if the pins
are not inserted into the mounting
holes in the sanding pad
5. Before using the tool, check that the Sanding Pad is securely fitted and the
bolt is tight
6. Select the required sanding sheet for your intended task (see ‘Selecting the
right grade of sanding sheet’ below)
7. The Sanding Pad and sanding sheets use a hook and loop system for
attachment. To mount the sheet carefully line up one corner of the sheet with
a corner of the Sanding Pad and gradually push the rest of the sheet on to
the pad, checking alignment as you do so, until the sheet is fitted correctly
(see Fig. D)
Selecting the right grade of sanding sheet
• Sanding sheets are available in a variety of different grades: coarse (60 grit),
medium (120 grit) and fine (240 grit)
• Use a coarse grit to sand down rough finishes, medium grit to smooth the work,
and fine grit to finish off
• Always use good quality sanding sheets to maximise the quality of the finished
task
• It is advisable to do a trial run on a scrap piece of material to determine the
optimum grades of sandpaper for a particular job. If there are still marks on your
work after sanding, try either going back to a coarser grade and sanding the
marks out before recommencing with the original choice of grit, or try using a
new piece of sandpaper to eliminate the unwanted marks before going on to a
finer grit and finishing the job
Operation
WARNING:
Always wear adequate personal protection equipment, including eye,
hearing and respiratory protection, when working with this tool.
WARNING:
Anti-vibration gloves should be worn when operating this tool, to
protect users from the effects of vibration produced by the tool.
Switching on and off
1. Hold the tool firmly by the Grip (2), with the thumb over the On/Off Switch (3)
2. Disengage the Safety Latch (4) and slide the On/Off Switch forward until it
locks, to switch the tool on
3. Push down on the bottom part of the On/Off Switch, to switch the tool off
WARNING:
Allow the tool to reach the required speed before making contact with
the workpiece.
WARNING:
Motor vents allow heat generated from the motor to escape the body of
the tool and must not become blocked. Dust, wood chippings and swarf can block
the motor vents and cause the tool to shut down. Swarf, created when cutting metal,
can also cause permanent damage if it enters the tool. Do not allow dust, wood
chippings and swarf to build up. Use a vacuum cleaner to keep the work space
clean, especially in confined areas, and when working with harmful substances.
WARNING:
DO NOT inhale dust. Wear adequate breathing protection. Some dusts
may be toxic especially from man-made composite materials.
Adjusting the tool speed
• The oscillating speed of this multi-tool can be adjusted over the Variable Speed
Dial (1)
1. Turn the Variable Speed Dial to a higher setting, to increase tool speed
2. Turn the Variable Speed Dial to a lower setting, to decrease tool speed
Note:
Adjust tool speed to best suit the work carried out, and to adapt to material
requirements. Also refer to the accessory manufacturer’s instructions, with regards
to tool speed selection.
Sawing
• Ensure the saw blade is sharp and in good condition
• Do not use saw blades that are damaged or deformed in any way
• When sawing light building materials, follow the recommendations of the
material suppliers
• Apply plunge cuts to soft materials ONLY, for example wood, plasterboard etc.
• If using saw blades not designed for cutting metal, ensure there are no nails or
screws embedded in the workpiece. If necessary, remove embedded objects or
use metal cutting saw blades instead
Sanding
• The removal rate and the sanding pattern are determined by the type of sanding
sheet, the preset oscillation rate and the applied pressure
• Pay particular attention to applying uniform sanding pressure; this increases the
working life of the sanding sheets
• Intensifying the sanding pressure will not lead to an increase of the sanding
capacity, but to increased wear of the machine and premature wear of the
sanding sheet
• For precise on-the-spot sanding of edges, corners and hard-to-reach areas, it is
also possible to work only with the tip or an edge of the sanding plate
• A sanding sheet that has been used for sanding metal should not be used for
sanding other materials
• Regularly brush down or vacuum the surface being sanded to ensure the
sanding sheet is in direct contact with the surface
Scraping
• For scraping, select a high speed setting
• On soft surfaces (e.g. wood), work at a flat angle and apply only light pressure
so that the scraper does not cut into the surface
Accessories
• A full range of oscillating multi-tool accessories, including different saw blades,
scrapers, grinding and sanding accessories is available from your Silverline
stockist
Maintenance
WARNING:
ALWAYS disconnect from the power supply before carrying out any
maintenance/cleaning.
General inspection
• Regularly check that all the fixing screws are tight. They may vibrate loose
over time
• Inspect the supply cord of the tool, prior to each use, for damage or wear.
Repairs should be carried out by an authorised Silverline service centre. This
advice also applies to extension cords used with this tool
Lubrication
• Lubricate all moving parts with a suitable lubricant spray, at regular intervals
Cleaning
WARNING:
ALWAYS wear protective equipment including eye protection and gloves
when cleaning this tool.
• Keep your tool clean at all times. Dirt and dust will cause internal parts to wear
quickly, and shorten the device’s service life
• Clean the body of your machine with a soft brush, or dry cloth
• Never use caustic agents to clean plastic parts. If dry cleaning is not sufficient, a
mild detergent on a damp cloth is recommended
• Water must never come into contact with the tool
• Ensure the tool is thoroughly dry before using it
• If available, use clean, dry, compressed air to blow through the ventilation holes
(where applicable)
Fig. C
Fig. D
PDF Compressor Pro
Summary of Contents for 243574
Page 3: ...2 9 2 1 8 7 4 5 3 6 7 10 ...
