www.silverlinetools.com
5
128965
Belt Sander 76mm
Power Tool Use & Care
a)
Do not force the power tool. Use the correct power tool for your
application.
The correct power tool will do the job better and safer at
the rate for which it was designed
b)
Do not use the power tool if the switch does not turn it on and off.
Any power tool that cannot be controlled with the switch is dangerous
and must be repaired
c)
Disconnect the plug from the power source and/or the battery
pack from the power tool before making any adjustments,
changing accessories, or storing power tools.
Such preventive
safety measures reduce the risk of starting the power tool accidentally
d)
Store idle power tools out of the reach of children and do
not allow persons unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous
in the hands of untrained users
e)
Maintain power tools. Check for misalignment or binding of
moving parts, breakage of parts and any other condition that
may affect the power tool’s operation. If damaged, have the
power tool repaired before use.
Many accidents are caused by
poorly maintained power tools
f)
Keep cutting tools sharp and clean.
Properly maintained cutting
tools with sharp cutting edges are less likely to bind and are easier
to control
g)
Use the power tool, accessories and tool bits etc. in accordance
with these instructions, taking into account the working
conditions and the work to be performed.
Use of the power tool for
operations different from those intended could result in a hazardous
situation
Service
a)
Have your power tool serviced by a qualified repair person using
only identical replacement parts.
This will ensure that the safety of
the power tool is maintained
Sanding Tool Safety
• Before connecting the tool to a power source, ensure that the voltage
supply matches that specified on the rating plate of the tool
• Always wear appropriate protective equipment, including dust mask
(suitable for very fine particulates), safety goggles and ear defenders
• Ensure all people in the vicinity of the work area are also equipped with
suitable personal protective equipment
• Take special care when sanding some woods (such as beech, oak,
mahogany and teak), as the dust produced is toxic and can cause
extreme reactions
• Do not sand magnesium or alloys containing a high percentage of
magnesium
• Be aware of paint finishes or treatments that may have been applied to
the material that is being sanded. Many treatments can create dust that
is toxic, or otherwise harmful. If working on a building constructed prior
to 1960, there is an increased chance of encountering lead-based paints
• The dust produced when sanding lead-based paints is particularly
hazardous to children, pregnant women, and people with high blood
pressure. Do not allow these people near to the work area, even if
wearing appropriate personal protective equipment
• Whenever possible, use a vacuum dust extraction system to control dust
and waste
• Be especially careful when using a machine for both wood and metal
sanding. Sparks from metal can easily ignite wood dust. Always clean
your machine thoroughly to reduce the risk of fire
• Work surfaces and sandpaper can become very hot during use, if there
is evidence of burning (smoke or ash), from the work surface, stop and
allow the material to cool. Do not touch work surface or sandpaper until
they have had time to cool
• Do not touch the moving sanding paper
• Always switch off before you put the sander down
• Always unplug the sander from the mains power supply before changing
or replacing sandpaper
• Even when this tool is used as prescribed it is not possible to eliminate
all residual risk factors. If you are in any doubt as to safe use of this tool,
do not use it
1
Front Handle
2
Lock On Button
3
Rear Handle
4
Dust Extraction Port
5
Drive Belt Housing Cover
6
Brush Access Caps
7
Belt Tracking Adjuster
8
On/Off Trigger
9
Speed Control Dial
10
Front Roller
11
Belt Release Lever
12
Depth Frame
13
Depth Adjustment Knob
14
Dust Bag
Product Familiarisation
Unpacking Your Tool
• Carefully unpack and inspect your tool. Fully familiarise yourself with all
its features and functions
• Ensure that all parts of the tool are present and in good condition. If
any parts are missing or damaged, have such parts replaced before
attempting to use this tool
Before Use
• Carefully unpack and inspect your sander. Fully familiarise yourself with
all functions/features of the tool
• Ensure that all parts of your sander are present and in good condition.
If any part is missing, or damaged, have such parts replaced before
attempting to use this tool. Always use dust extraction where available,
or a dust bag where not
Fitting sanding belts
WARNING:
Before fitting sanding belts, ensure that the sander is
disconnected from the power supply.
• To fit a new sanding belt, first remove the Depth Frame (12), if fitted
• Place the sander upside down on a workbench or similar solid, flat
surface
• Pull out the Belt Release Lever (11). This retracts the Front Roller (10) and
slackens the sanding belt. The worn belt can now be removed
• Fit the new sanding belt, positioning it squarely over the rollers
• Close the belt release lever. The belt should now be taut and secure
• Once fitted, it may be necessary to adjust the front roller to ensure that
the belt runs true
• Keep the sander inverted on the work bench, and connect it to power
• Hold the sander firmly by the Rear Handle (3) and depress the On/Off
Trigger (8). Observe any sideways motion of the belt
• If needed, turn the Belt Tracking Adjuster (7) clockwise to move the belt
left, or anti-clockwise to move the belt right until the belt runs true
• Disconnect the sander from power
128965_Z1MANPRO1.indd 5
10/05/2012 11:40
