SILLA PRISM SOLAR RFID Instructions For Installation, Use And Maintenance Manual Download Page 46

Page: 46 / 52

Led Indicator Color Chart

LEDs located on the front cover of Prism indicate the status of use, and any
malfunctions that occur during use.

LED

Led bar color

Button

color

Status

Description

First led down

light

blue

Light blue

STAND BY

Prism is on standby,

ready for charging.

green

moving LEDs

green

CHARGING

Vehicle charging
regularly.

green

bottom led,

top led

yellow

(

depending on the

percentage of

energy from
photovoltaics)

moving

yellow

SOLAR

Use of solar

generation for

charging.

All

purple

UPDATE

A Prism update is in

progress. The device
will reboot when the

update is complete.

LED

Led bar color

Button

color

Status

Description

Prism SOLAR rel. 2.2.2

Summary of Contents for PRISM SOLAR RFID





















































Search results

Summary of Contents for PRISM SOLAR RFID

Reviews:

Related manuals for PRISM SOLAR RFID

Brands by name

Popular brands

SILLA PRISM SOLAR RFID, Instructions For Installation, Use And Maintenance Manual

Search results

Summary of Contents for PRISM SOLAR RFID

Reviews:

Related manuals for PRISM SOLAR RFID

Brands by name

Popular brands