SILLA PRISM SOLAR RFID Instructions For Installation, Use And Maintenance Manual Download Page 20 | Manualshive

Page: 20 / 52

background image

Connecting the sensor to Prism Three-phase

For three-phase Prism, the sensor must be connected as follows:

Connection marking

Connection marking

A+ RS485

A+

B- RS485

B-

GND

G

Terminating resistors:

The

120 ohm terminating resistor

is connected to the end of the cable at the meter

terminals. Inside Prism, check that the jumper on the right-hand side of the connector is
correctly installed.

Cables:

●

The communication line is RS485 at 9600bps

●

The length of the cables should not exceed 200 metres

●

Use a

twisted and shielded twisted pair, with GND conductor, with a

recommended cross section of 0.25-0.5 mm2.

For distances less than 100 m, a pair of CAT5 cable or similar can be used. Preferably,
choose a cable suitable for RS485/Modbus communication.

18

-

Prism SOLAR rel. 2.2.2

«
...
18
19
20
21
22
...
»

Summary of Contents for PRISM SOLAR RFID





















































Reviews:

No comments

Related manuals for PRISM SOLAR RFID

Brand: EAE Pages: 36

Brand: Xantrex Pages: 4

Brand: Xantrex Pages: 20

STRONG-BAC 20TB

Brand: Caldwell Pages: 11

Brand: Aiwa Pages: 30

StorageWorks DS-BA35X-MN

Brand: Digital Equipment Pages: 2

Brand: ICP DAS USA Pages: 2

Brand: M-system Pages: 5

Brand: First Power Pages: 16

Brand: Major Pages: 44

Brand: Rotary Pages: 12

Brand: Rehasense Pages: 6

Brand: Fenix Pages: 24

Brand: ICP DAS USA Pages: 4

ADDIALOG PA 3110

Brand: Addi-Data Pages: 73

Brand: PVI Pages: 12

Brand: Peak Pages: 41

Brand: iSMA CONTROLLI Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands