SILLA PRISM SOLAR RFID Instructions For Installation, Use And Maintenance Manual Download Page 47

Page: 47 / 52

ﬁrst led up

red

ERROR SENSOR

External sensor is
not conﬁgured or is

not working.

Warning.

balancing

will not work, may
jump the meter.

ﬁrst led on top

purple

ERROR

CONNECTION

Server connection
error. Remote

functionality may not
work

some

red

leds

red

ERROR

Different
combinations of the

LEDs represent error
warnings.
If all LEDs are red, it

is necessary to
disconnect the

connector, remove
power to Prism, and
contact service.

Orange

LEDs

orange

WAITING FOR

AUTHORIZATION

Prism is waiting for
authorization to start

charging. Refer to
the section

The RFID

display

to enable

charging

Prism SOLAR rel. 2.2.2

- 41

Summary of Contents for PRISM SOLAR RFID





















































Search results

Summary of Contents for PRISM SOLAR RFID

Reviews:

Related manuals for PRISM SOLAR RFID

Brands by name

Popular brands

SILLA PRISM SOLAR RFID, Instructions For Installation, Use And Maintenance Manual

Search results

Summary of Contents for PRISM SOLAR RFID

Reviews:

Related manuals for PRISM SOLAR RFID

Brands by name

Popular brands