manualshive.com logo in svg

Silicon Graphics InfiniteStorage 4000 Series, Configuring And Maintaining, Page: 59 / 276

Share
Download
Silicon Graphics InfiniteStorage 4000 Series Configuring And Maintaining Download Page 59

Chapter 3: Configuration Concepts

47

NOTE  

Snapshot (Legacy) Volume and Synchronous Mirroring are premium features 

that you must activate before you can use them. For more information about snapshot 

(legacy) volumes, see “

Using the Snapshot (Legacy) Premium Feature

.” For more 

information about Synchronous Mirroring, see “

Using the Synchronous Mirroring 

Premium Feature

.”

The number and capacity of the volumes in your storage array depends on the type of 

controller in the storage array. The following table lists the maximum number of 

volumes in a storage array that each controller model supports.

Table 8  Maximum Number of Volumes Each Controller Model Supports

NOTE  

The maximum volume size is limited by the size of the drives and the 

configuration of the storage array. The last 512 MB on each drive is reserved for 

storage array configuration database and potential future expansion. For practical 

considerations, you want to constrain the maximum volume size so that drive 

replacement and volume reconstruction does not take an excessive amount of time.

Specification

E2600

E5400

E5500

Maximum number of volumes per 

storage array

512

2048

2048

Maximum number of volumes per 

volume group

256

256

256

Maximum number of volumes per 

disk pool

512

2048

2048

Maximum volume size for a 

volume group

Number of drives supported by array 

x (capacity of largest supported 

drive by array – 512 MB

Maximum volume size for a disk 

pool

64 TB

64 TB

64 TB

Maximum number of drives per 

volume group using  RAID 

Level 5

30

30

30

Maximum number of drives per 

disk pool using RAID Level 6

192

192

192

Maximum number of remote 

mirrors

16

16

128

Summary of Contents for InfiniteStorage 4000 Series





















































































































































































































































































Reviews:

No comments