manualshive.com logo in svg

Silicon Graphics InfiniteStorage 4000 Series, Configuring And Maintaining

The Silicon Graphics InfiniteStorage 4000 Series is a high-performance data storage solution designed for seamless integration into any IT environment. Unlock the full potential of your system with its user-friendly interface and advanced features. Access the free user manual at manualshive.com to optimize your experience with this exceptional product.

Share
Download
background image

Chapter 7: Using the Asynchronous Mirroring Premium Feature

121

7

Using the Asynchronous Mirroring Premium Feature

The Asynchronous Mirroring premium feature provides for replicates the data 

between storage arrays over a remote distance. In the event of a disaster or a 

catastrophic failure on one storage array, you can promote the second storage array to 

take over responsibility for computing services. Asynchronous mirroring is designed 

for extended storage environments in which the storage arrays that are used for 

asynchronous mirroring are maintained at separate sites. Volumes on one storage 

array are mirrored to volumes on another storage array across a fabric SAN. Because 

asynchronous mirroring is storage based, it does not require any server overhead or 

application overhead.
Asynchronous mirroring is managed on a per-volume basis, enabling you to associate 

a distinct remote mirrored volume with one or more primary volume on a given 

storage array. Point-in-time images are used on the primary volume and the secondary 

volume to batch the resynchronization process. A data repository volume is required 

for each mirrored volume. Also, you can create asynchronous mirror groups that 

enable you to manage the synchronization process as a set to create consistent data on 

the remote storage array. 
Asynchronous mirroring can use either Fibre Channel or iSCSI to communicate with 

the remote array. Inter-controller communication for asynchronous mirroring uses the 

host-connected ports to initiate connections to the remote system. The iSCSI 

inter-controller communication must use a host-connect port, not the management 

Ethernet port. A controller can receive host I/O through one protocol and use a 

different protocol for asynchronous mirroring with a remote storage array. For 

example, a host can be attached to the controller through a SAS connection while the 

inter-controller mirroring data is sent over ISCSI to the remote storage array.
The asynchronous write mode of the legacy Synchronous Mirroring premium feature 

is still supported, but the new Asynchronous Mirroring premium feature is the 

preferred method to use if available on your storage array. Some key differences 

between Asynchronous Mirroring premium feature and the Synchronous Mirroring 

premium feature are these:

With the Asynchronous Mirroring premium feature, a data repository volume is 

required for each mirror. The Synchronous Mirroring premium feature has a 

single repository for all mirrored volumes.

The Asynchronous Mirroring premium feature uses point-in-time images on the 

primary and secondary volumes to batch the resynchronization process. 

The Asynchronous Mirroring premium feature organizes mirrored volumes into 

groups to manage the synchronization process to create a consistent data set on 

the remote storage array.

The Asynchronous Mirroring premium feature supports iSCSI and Fibre Channel 

connections between storage arrays. The Synchronous Mirroring premium 

feature supports only Fibre Channel connections.

Summary of Contents for InfiniteStorage 4000 Series





















































































































































































































































































Reviews:

No comments

Related manuals for InfiniteStorage 4000 Series

IBM RS/6000 7043 43P Series User Manual preview
RS/6000 7043 43P Series
Brand: IBM Pages: 322
IBM System x3400 M3 Types 7378 Product Manual preview
System x3400 M3 Types 7378
Brand: IBM Pages: 45
IBM Storwize V7000 Quick Installation Manual preview
Storwize V7000
Brand: IBM Pages: 102
Yamaha AW4416 Manual preview
AW4416
Brand: Yamaha Pages: 3
QNO 2WAN 3LAN User Manual preview
2WAN 3LAN
Brand: QNO Pages: 106
Face XR18 User Manual preview
XR18
Brand: Face Pages: 8
Intenso 2,5" EXTERNAL HARD DRIVE KIT User Manual preview
2,5" EXTERNAL HARD DRIVE KIT
Brand: Intenso Pages: 94
Apricorn Aegis NetDock Quick Start Manual preview
Aegis NetDock
Brand: Apricorn Pages: 4
TRENDnet TW-100 Specifications preview
TW-100
Brand: TRENDnet Pages: 2
Weidmuller IE-SW-VL16-14TX-2SC Hardware Installation Manual preview
IE-SW-VL16-14TX-2SC
Brand: Weidmuller Pages: 17
Megatank GL48100 Operation Manual preview
GL48100
Brand: Megatank Pages: 12
Lancom GS-2310P Instruction Manual preview
GS-2310P
Brand: Lancom Pages: 25
Abocom HomePlug AV Ethernet Bridge PLE0200 Quick Install preview
HomePlug AV Ethernet Bridge PLE0200
Brand: Abocom Pages: 2
B&B Electronics Vlinx VESP211 Manual preview
Vlinx VESP211
Brand: B&B Electronics Pages: 67
Salsbury Industries 18-51000 Series Installation Instructions preview
18-51000 Series
Brand: Salsbury Industries Pages: 5
Quantum 7000DLT Series Product Manual preview
7000DLT Series
Brand: Quantum Pages: 312
Conel UR5i v2 SL User Manual preview
UR5i v2 SL
Brand: Conel Pages: 32
Digisol DG-BG4100NU Quick Installation Manual preview
DG-BG4100NU
Brand: Digisol Pages: 22

Brands by name

Popular brands

Load more brands