background image

238

Show Drive Channel Stat 

DRIVE CHANNEL 7 

   Port: 5, 6 

   Status:  Optimal 

   Max. Rate: 4 Gbps 

   Current Rate: 2 Gbps 

   Rate Control: Auto 

   Controller A link status: Up 

   Controller B link status: Up 

   Trunking active: No 

 

   DRIVE COUNTS 

 

      Total # of attached drives: 0 

 

      CUMULATIVE ERROR COUNTS 

         Controller A 

            Baseline time set:              10/30/10 

1:15:59 PM 

            Sample period (days, hh:mm:ss): 32 days, 

00:55:04 

            Controller detected errors:     0 

            Drive detected errors:          0 

            Timeout errors:                 0 

            Link down errors:               0 

            Total I/O count:                131818784 

 

         Controller B 

            Baseline time set:              10/30/10 

1:15:59 PM 

            Sample period (days, hh:mm:ss): 32 days, 

00:53:22 

            Controller detected errors:     0 

            Drive detected errors:          0 

            Timeout errors:                 0 

            Link down errors:               N/A 

            Total I/O count:                13171844 

 

 

DRIVE CHANNEL 8 

   Port: 7, 8 

   Status:  Optimal 

   Max. Rate: 4 Gbps 

   Current Rate: 4 Gbps 

   Rate Control: Auto 

   Controller A link status: Up 

   Controller B link status: Up 

Summary of Contents for InfiniteStorage 4000 Series





















































































































































































































































































Reviews: