manualshive.com logo in svg

Silicon Graphics InfiniteStorage 4000 Series, Configuring And Maintaining

The Silicon Graphics InfiniteStorage 4000 Series is a high-performance data storage solution designed for seamless integration into any IT environment. Unlock the full potential of your system with its user-friendly interface and advanced features. Access the free user manual at manualshive.com to optimize your experience with this exceptional product.

Share
Download
background image

Chapter 1: About the Command Line Interface

13

Set Storage Array 
AutoSupport Bundle 
Disable

This command turns off the AutoSupport (ASUP) bundle collection and transmission 

for the storage array. You can run this version of the command from the script editor 

or in a script file.

Syntax

set storageArray autoSupport disable

Parameters

None.

Minimum Firmware Level

7.86

Set Storage Array 
AutoSupport Bundle 
Enable

This command turns on the AutoSupport (ASUP) bundle collection and transmission 

for the storage array.

Syntax

set storageArray autoSupport enable

Parameters

None.

Minimum Firmware Level

7.86

Test AutoSupport 
Configuration

NOTE  

This command is an SMcli command, no

t

 a script command. You must run this 

command from a command line. You cannot run this command from the script editor 

in the storage management software

This command validates the current auto support configuration by sending a test 

ASUP bundle and reports the result of the test transmission.

Syntax

SMcli -supportBundle testConfig

Parameters

None

Minimum Firmware Level

7.86

Summary of Contents for InfiniteStorage 4000 Series





















































































































































































































































































Reviews:

No comments

Related manuals for InfiniteStorage 4000 Series

DANE-ELEC SO MOBILE Datasheet preview
SO MOBILE
Brand: DANE-ELEC Pages: 2
FOR-A MFR-4000 Operation Manual preview
MFR-4000
Brand: FOR-A Pages: 72
Seagate Hawk 1 ST11200N Product Manual preview
Hawk 1 ST11200N
Brand: Seagate Pages: 84
BSD Networks bsg-0800t User Manual preview
bsg-0800t
Brand: BSD Networks Pages: 7
Sans Digital AccuRAID AR316X12 Quick Installation Manual preview
AccuRAID AR316X12
Brand: Sans Digital Pages: 8
Ideon Audio Absolute Stream User Manual preview
Absolute Stream
Brand: Ideon Audio Pages: 24
Kohler Mira Pixel User Manual preview
Mira Pixel
Brand: Kohler Pages: 32
IBM OpenPower 720 Technical Overview And Introduction preview
OpenPower 720
Brand: IBM Pages: 74
Ubiquiti EdgeRouter PoE ERPoe-5 Quick Start Manual preview
EdgeRouter PoE ERPoe-5
Brand: Ubiquiti Pages: 13
G-Technology G-DRIVE mobile USB Product Manual preview
G-DRIVE mobile USB
Brand: G-Technology Pages: 32
Quantum DLT 2500 Product Manual preview
DLT 2500
Brand: Quantum Pages: 345
Broadband Products D-Link DSL-2640U Quick Installation Manual preview
D-Link DSL-2640U
Brand: Broadband Products Pages: 12
Planet VC-820M Quick Installation Manual preview
VC-820M
Brand: Planet Pages: 2
TP-Link JetStream T2600G-28TS User Manual preview
JetStream T2600G-28TS
Brand: TP-Link Pages: 1136
H3C AR 46-80 Installation Manual preview
AR 46-80
Brand: H3C Pages: 103
Edimax EDIMAX FAST ETHERNET MFP SERVER VERSION: 2.0 User Manual preview
EDIMAX FAST ETHERNET MFP SERVER VERSION: 2.0
Brand: Edimax Pages: 118
Toto Link ND300V2 Manual preview
ND300V2
Brand: Toto Link Pages: 57
Linksys NAS200 User Manual preview
NAS200
Brand: Linksys Pages: 43

Brands by name

Popular brands

Load more brands