SILENTRON SERENYA 2000, Manual

Page: 6 / 20

COPYRIGHT SERENYA COD. 2001
SERENYA
by Silentron
– made in Italy
Identification: the correct vocal recording and writing of the "labels" of the various detectors in the programming phase allows the user to
receive all messages with the exact indication regarding the device of interest.
2.2.3) HOME AUTOMATION FUNCTIONS
A) Programmable clock:
the control unit has a programmable clock for forced arming (voir 3.2.6)
B) Radio Outputs: 16 radio commands are available to command local radio switches, to be activated via telephone calling the control panel to
switch-on lights or other electrical charges. These receivers can also be activated via key-fobs, keypads, detectors (look 3.3 and followings)
2.3) FUNCTIONING OF THE SIRENS - ALSO SEE SPECIFIC MANUAL
The control panels control the indoor and outdoor radio sirens:
a) Indoor sirens: they emit an arming (partial/full 3 Beeps) and disarming (just one Beep) acoustic signal, the intensity of which can be
regulated to zero. The signal is set off for 3 minutes in the case of a general, tamper or panic alarm.
b) Outdoor sirens: they emit an arming (partial/full 3 Beeps) and disarming (just one Beep) acoustic signal, the intensity of which can be
regulated to zero and they flash at the same time. The sirens activate for 3 minutes in the case of a general, tampering or panic alarm after a
pre-alarm period of about 10 seconds, during which an intermittent acoustic signal is emitted. This delay, which cannot be changed, is intended
to prevent disturbance if one forgets to disarm the system. In the case of EXTERNAL ALARM programming the outdoor sirens are not triggered,
but the pre-alarm condition continues for up to 3 minutes or a recorder dissuasive message is played (code 2032).
3) THIRD PART
– CONTROL PANEL FUNCTIONING
3.1) SECURITY PROTECTION
– USER CODE – INSTALLER CODE
The control unit is provided with a factory
code “0 0 0 0” which allows access to the programming procedure. During installation it is necessary
to change this code, programming other two ones (differents between them): USER code and INSTALLER code.
In case of lost or forgotten codes the only solution consists in open the control panel generating a Tamper alarm, disconnect and connect again
power supply and begin entering the factory code: this operation doesn’t delete the realized programming.
a) INSTALLER CODE: from 4 to 8 digits, which allows access to all programming but not operations.
b) USER CODE: from 4 to 8 digits, it allows the followings functions

placing the control unit in TEST mode for testing or battery change.

reading the EVENTS MEMORY

programming/modification of listed telephone numbers (see third part)

recording/modification of all vocal messages (see third part)

addition/deletion of remote controls and/or numeric arming/disarming codes (see third part)

modification of supplementary wired key function (see third part)

modification of certain SETTINGS: Exclusion of radio or wired detectors (sensors)
– Clock/date setting – Change of user code – Change of
daylight-saving time
– Change of display back-lighting – Regulation of vocal message volume - Change of automatic forced arming – Control
unit firmware version check
Attention! Careless with the USER code can limit the efficiency of the entire system, therefore, it is advisable to be informed on the various
functions before making any changes.
3.2) USER’s OPERATIONS –
NORMAL SITUATION OF THE CONTROL PANEL
13 / 02 / 09 17,00
DISARMED _ ▄ █ █
DATE TIME
STATUS GSM SIGNAL
Date and time must be correctly programmed and upgraded at least every 6 months
(maintenance): look at the SETTINGS menù
3.2.1) ARMING - DISARMING USING THE CONTROL UNIT KEYPAD (VISUAL, VOCAL CONFIRM)
3.2.2) OPERATIONS WITH REMOTE CONTROLS AND/OR ADDITIONAL KEYPADS
TOTAL ARMING
Supplementary keypads:
enter the numerical code and then press the red key
KEY-FOBS: press the red key
PARTIAL ARMING
(vocal confirm or a long Beep)
Supplementary keypads: enter the numerical code, by pressing A, B, C exclude the zones that are not to be armed and then press the red key
KEY-FOBS: press the white key to arm zones A+B (for other solutions see the remote control instructions)
DISARMING
13 / 02 / 09 17,00
DISARMED _ ▄ █
Arming :enter the 5 digits code and
press the button


ARM GROUPS :
A B C
Select partitions to don’t arm using
the buttons 1,2,3 and press the button


13 / 02 / 09 17,00
ARMED A B C _ ▄ █
Disarming : enter the 5 digits code
and press the button


13 / 02 / 09 17,00
DISARMED _ ▄ █
The control panel confirms the operations.
If new events are happened a vocal
message infor the USER