manualshive.com logo in svg

Siemens SITRANS FUE950, Operating Instructions Manual, Page: 26 / 72

Share
Download
Siemens SITRANS FUE950 Operating Instructions Manual Download Page 26

Connecting 

 

5.1 SITRANS FUE380 and FUS380 

5.1

 

SITRANS FUE380 and FUS380 

Power for pulse output from SITRANS FUE380 and FUE380 is automatically supplied via 

energy calculator terminals 10 and 11: 

 

FUE380/FUS380 terminal 

FUE950 terminal 

56 

10 

57 

11 

 

 

 

56
57

 

 

FUE380/FUS380 

FUE950 

 

 

Note 

 

Use shielded cable. Connect shield to grounding at flowmeter (e. g. the clamp of FUE380). 

 

For connection of flowmeter, see flowmeter operating instructions. 

5.2

 

SITRANS F M MAG 5000/6000 

When MAG 5000/6000 and SITRANS FUE950 are connected as a heat meter, 2 resistors 

are required to obtain a correct transmission of pulses. 
The 2 resistors must be mounted between terminals 57 and 58 in the MAG terminal socket. 
Resistors are part of neither delivery nor accessories list. 

 

MAG 5000/6000 terminal 

FUE950 terminal 

57 

10 

58 

11 

 

 

SITRANS FUE950 

24

 

Operating Instructions, 01/2010, SFIDK.PS.022.F4.02 

Summary of Contents for SITRANS FUE950









































































Reviews:

No comments