Siemens SITRANS FUE950 Operating Instructions Manual Download Page 18 | Manualshive

Page: 18 / 72

Siemens SITRANS FUE950 Operating Instructions Manual Download Page 18

Installing/Mounting

4.3 Application settings

Installation safety precautions

WARNING

In applications with working pressures/media that can be dangerous to people,

surroundings, equipment or others in case of pipe fracture, it is recommended that special

precautions such as special placement, shielding or installation of a security guard or a

security valve are taken when the temperature sensors are mounted.

4.3

Application settings

Check of application settings

● Application and flow meter installation place

Application type and flow meter installation place can be checked via order code on

device type label.
- Calculator district heating, flow meter in return line (cold pipe) 7ME3470-xxAx-xxxx
- Calculator district heating, flow meter in forward line (warm pipe) 7ME3470-xxBx-xxxx
- Calculator chilled water, flow meter in forward line (cold pipe) 7ME3470-xxCx-xxxx
- Calculator chilled water, flow meter in return line (warm pipe) 7ME3470-xxDx-xxxx
- Calculator combined cooling/ heating, flow meter in forward line (warm pipe by heating)

7ME3470-xxEx-xxxx
- Calculator combined cooling/ heating, flow meter in return line (cold pipe by heating)

7ME3470-xxFx-xxxx

● Pulse input setting

Calculator pulse input setting must fit flowmeter pulse output setting (e.g. ultrasonic

flowmeter type SITRANS FUE380). Check both type plates for settings.

● Pt sensor type.

Observe information of temperature sensor installation.

● Max. flow rate.

Max. flow rate for energy calculator must not be exceeded.

SITRANS FUE950

16

Operating Instructions, 01/2010, SFIDK.PS.022.F4.02

«
...
16
17
18
19
20
...
»

Summary of Contents for SITRANS FUE950









































































Reviews:

No comments