manualshive.com logo in svg

Siemens SITRANS FUE950, Operating Instructions Manual, Page: 10 / 72

Share
Download
Siemens SITRANS FUE950 Operating Instructions Manual Download Page 10

Safety notes 

 

2.2 Lithium batteries 

2.2

 

Lithium batteries 

Lithium batteries are primary power sources with high energy content designed to represent 

the highest possible degree of safety. 

 

WARNING 

 

Potential hazard 
Lithium batteries may present a potential hazard if they are abused electrically or 

mechanically. This is in most circumstances associated with the generation of excessive 

heat where internal pressure may cause the cell to rupture.  
Thus the following basic precautions should be observed when handling and using lithium 

batteries: 

•

 

Do not short-circuit, recharge or connect with false polarity. 

•

 

Do not expose to temperature beyond the specified temperature range or incinerate the 

battery. 

•

 

Do not crush, puncture or open cells or disassemble battery packs. 

•

 

Do not weld or solder to the battery’s body. 

•

 

Do not expose contents to water. 

 

2.3

 

General requirements 

The label seal on the calculator (see figures (Page 49)) must not be damaged! 
A damaged seal will result in immediate invalidation of the factory warranty and calibration. 
Siemens accepts no liability for amendment of legal metrological data if the seal has been 

broken. 
The cables supplied with the calculator must not be shortened or altered in any other way. 

 

Note 

 

All regulations on the use of calculator must be observed! 
All regulations on electrical installations must be observed! 
All instructions listed in the data sheet of the calculator must be observed. 
The medium is fixed to water (or - as special option - for glycol additive) with specified 

consistence. 

 

Note 

 

Calibration/verification 
SITRANS FUE950 is a calorific energy meter ready for verification in accordance MID 

approval according to European norm EN 1434. 
Calibration marks on the calculator must not be damaged or removed! Their removal 

invalidates the warranty and calibration of the meter. Label seals may only be removed by 

authorized persons for servicing purposes and must then be renewed. 

 

 

SITRANS FUE950 

8

 

Operating Instructions, 01/2010, SFIDK.PS.022.F4.02 

Summary of Contents for SITRANS FUE950









































































Reviews:

No comments