manualshive.com logo in svg

Siemens SITRANS F FS200 Utility, Programming Manual, Page: 34 / 36

Share
Download
Siemens SITRANS F FS200 Utility Programming Manual Download Page 34

34

Glossary

% Accepted

Percentage of all acoustic transmit/receive signals used for flow measurement analysis. 100%

is perfect. If application conditions such as aeration or noise interference are present this

number may decrease.

AGA-8

The AGA8 function is used to calculate the compressibility factor of natural gas and related

hydrocarbon gases. The internal AGA8 lookup table provides for the actual gas density and

compressibility factor (Z Actual) for the indicated pressure and temperature. These values

are then used to compute either mass flow rate or standard volume corrected flow rate.

Channel

An assignable input / output terminal for the purpose of connecting communication cabling,

I/O signal wiring or RTDs to an FS230 Flowmeter.

Correlation Q

Quality of correlation (phase coherency) between the upstream and downstream receive

signals. Cor-Q ranges from 0.9 to 1.0, where 1.0 indicates perfect correlation and 0.9

indicates ambiguous or poor correlation. Poor correlation is generally a result of acoustic

“beam blowing” due to high flow velocities in gas applications. Cor-Q can be improved

through an “HF” adjustment in the flowmeter.

Delta-time
(uSec)

Transit-time difference between upstream and downstream receive signals caused by flow

velocity. It is measured in microseconds.

Estimated Repeatability

The estimation of the maximum deviation in agreement between the results of

successive flow measurements carried out under the same conditions.

Path (N)

One of at least two (or four) physical flow measurement channels that comprise a multi-

path (or multi-beam) flow meter.

RxGain

Amplifier Gain setting that responds to varying receive signal amplitude. Lower is

better. Values undue 40 are acceptable for flow measurement.

Signal

The digitized acoustic (Receiver) signal.

FS2

0

0 Programming Manual, 03/2020,

 

A5E02951525-AB

Summary of Contents for SITRANS F FS200 Utility





































Reviews:

No comments