manualshive.com logo in svg

Siemens SITRANS F FS200 Utility, Programming Manual, Page: 30 / 36

Share
Download
Siemens SITRANS F FS200 Utility Programming Manual Download Page 30

30

Utility Screens

Sensor Selection

1. Liquid applications can be serviced by any of 3 sensor types as follows;

∂

High Precision:   The primary choice for steel pipes

∂

Universal:

For all non-steel and plastic pipes

∂

High Temperature:  For all pipes with temperatures between 250 – 450F

2. The FS200 Liquid Tool will recommend the best suited sensor type and size based on

your programmed application data parameters. In many cases more than one type sensor

is acceptable. The FS200 tool will identify these sensors with the indication

“Recommended” or with an asterisk (*). Alternate types can be selected so long as you

choose recommended types and sizes, be aware if an “Application Problem” alert appears

3. The FS200 utility will also provide the recommended sensor part number and the

recommended mounting method

Figure 6-12 Liquid Sensor Type / Size Selection

Clamp-On Liquid Tool screen

The Clamp-On Liquid Tool screen presents data in 2 available views; [Application Calcs] and

[Repeatability Graph].  You may click on the appropriate tab for specific details related to the

specified application. The data shown under each tab is relative to the application parameters

you entered for pipe dimensions, liquid type, flow, and temperature in the liquid tool using the

units of measure you selected. Should an application conflict exist it will alert you with an

“Application Problem” message.

Application Calcs. Tab

Click on the [Application Calcs] tab for application specific information pertinent to the

installation of your flow sensors, including spacing recommendation and offset (LTN).

Additionally, fundamental data relative to transit-time values, signal phase shift, Reynolds

number, flow velocity range and repeatability are also presented in this view

Figure 6-13 Liquid Application Calculations

FS2

0

0 Programming Manual, 03/2020,

 

A5E02951525-AB

Summary of Contents for SITRANS F FS200 Utility





































Reviews:

No comments