manualshive.com logo in svg

Siemens SITRANS F FS200 Utility, Programming Manual, Page: 31 / 36

Share
Download
Siemens SITRANS F FS200 Utility Programming Manual Download Page 31

Utility Screens

Repeatability Graph Tab

The [Repeatability Graph] tab provides performance data relative to the estimated

repeatability of your flowmeter over your specified flow range. Additionally, it provides

specifications for Reynolds number (Nr) transitional-flow start / end based on pipe

dimensions, viscosity and flow range. Nr data is useful in evaluating the potential for

measuring flow in transitional conditions.

Figure 6-14 Liquid Repeatability Data

Application Problems Tab

If any of your entered application parameters conflict with performance capabilities of

the FS230 flowmeter an “Application Problem” message will appear at the bottom of

the screen; this will cause an additional tab to open [Application Problems] (See Figure

6-15 below). Click on the [Application problem] tab to view a description of the

conflict(s). If no conflicts are present the tab will not appear.

Figure 6-15 Liquid Application Problems Screen

FS2

0

0 Programming Manual, 03/2020,

 

A5E02951525-AB

31

Summary of Contents for SITRANS F FS200 Utility





































Reviews:

No comments