Siemens SITRANS F FS200 Utility Programming Manual Download Page 12 | Manualshive

Page: 12 / 36

Siemens SITRANS F FS200 Utility Programming Manual Download Page 12

Setup Screens

12

4.3 Setup Menu

The [Setup] menu consists of two sub-menus:
● Communications
● Pass/Fall Limits

Figure 4-4 Setup Selection

Note
The [Pass/Fail Limits] menu appears only after a connection to the flowmeter has been

established via the [Connection] and [Connect] menus.

Communications Setup Screen

The [Communications Setup] screen is used to configure the FS200 utility communication

protocol data for connection to the flowmeter. It was covered in detail in section 3

Pass/Fall Limits Setup Screen

This screen enables the user the ability to modify the FS200 default numerical Warning

and Fail limits pertaining to proper flowmeter operation. These limits will be expressed

as Yellow (warning) or Red (Fail) indications when observing the Diagnostic data

screen of the FS200 utility. This screen displays the last saved input data settings.

Figure 4-5 Pass / Fail Limit Settings

FS2

0

0 Programming Manual, 03/2020,

A5E02951525-AB

«
...
10
11
12
13
14
...
»

Summary of Contents for SITRANS F FS200 Utility





































Reviews:

No comments