manualshive.com logo in svg

Siemens SITRANS F FS200 Utility, Programming Manual, Page: 20 / 36

Share
Download
Siemens SITRANS F FS200 Utility Programming Manual Download Page 20

20

Diagnostic Screens

Siemens Data Capture Log

FS200 Utility Version

1.00.02

Long Tag
Product S/N

N1J4118000027

COMS Settings

Baud:19200

Parity:None

Data Bits:8

Location Identifier
Meter Bore id

3.937 inches

System Setup Parameters
------------------------------------------------------------------------------

Parameter

Value

Units

Pipe Diameter

4.537 inches

Pipe Wall Thickness

0.3 inches

Pipe Inside Diameter

3.937 inches

Transducer Size

D4H

______________________________________________________________________________
Path Setup Parameters
Parameter

Path 1

Path 2

Units

Mounting Mode

Direct

Direct

Sensor Spacing LTN

0.4204

0.4204 inches

Sensor Frequency

187500

187500 Hz

Vsmin

197.2924

197.2924 mps

Vsmax

402.7076

402.7076 mps

______________________________________________________________________________
Column#

Label

Description

1

Date

Query Date

2

Time

Query Time

3

Flow Rate(m3/h)

Meter Flow Rate(m3/h)

4

Status FR

Status Flow Rate

7

VF1(m/s)

Flow Velocity path 1(m/s)

9

Avg VF(m/s)

Avg. Flow Velocity(m/s)

10

VoS1(m/s)

VoS path 1(m/s)

12

Avg VoS(m/s)

Avg. VoS(m/s)

13

Status 1

Status path 1

14

Status 2

Status path 2

15

RX Gain(up) 1

Upstream Xmit RX Gain(up) path 1

17

RX Gain(dn) 1

Downstream Xmit RX Gain(dn) path 1

19

DT 1(uS)

Transit-time Delta path 1(uS)

21

SNR(up) 1

Upstream Xmit SNR(up) path 1

23

SNR(dn) 1

Downstream Xmit SNR(dn) path 1

25

CorQ 1

Correlation Factor path 1

27

%ACP 1

Accepted Burst Percentage path 1

29

Temp(F)

Temperature(F)

30

Press(PSIA)

Pressure(PSIA)

31

Density(lbm/ft3)

Density(lbm/ft3)

32

Viscosity(cS)

Viscosity(cS)

Date

Time

Flow Rate(m3/h)  Status FR

Standard
Volume Flow

Rate(Nm3/h)

Status SVFR

VF1(m/s)

VF2(m/s)

VoS1(m/s)

3/16/2020

13:19:22

136.1288 Pass

1928.6162 Pass

5.096

4.953 361.49

3/16/2020

13:19:25

136.0898 Pass

1927.9778 Pass

5.126

4.934 361.33

3/16/2020

13:19:28

136.1612 Pass

1928.4122 Pass

5.112

4.948 361.48

3/16/2020

13:19:31

136.0763 Pass

1927.1472 Pass

5.096

4.955 361.52

3/16/2020

13:19:34

135.934 Pass

1924.6659 Pass

5.08

4.976 361.59

3/16/2020

13:19:37

136.0927 Pass

1927.6021 Pass

5.045

4.999 361.49

3/16/2020

13:19:40

136.0052 Pass

1925.5692 Pass

5.03

5.014 361.5

3/16/2020

13:19:43

135.755 Pass

1922.4499 Pass

5.029

4.996 361.45

3/16/2020

13:19:46

135.6573 Pass

1920.7065 Pass

5.058

4.971 361.55

3/16/2020

13:19:49

136.0195 Pass

1927.0039 Pass

5.06

4.984 361.63

3/16/2020

13:19:52

136.1911 Pass

1928.8372 Pass

5.07

4.984 361.61

Average Value

136.0101

1926.2717

5.073

4.974 361.51

Minimum

136.1911

1928.8372

5.126

5.014 361.33

Maximum

135.6573

1920.7065

5.029

4.934 361.63

Warning Limit

Simulation Mode

Simulation Mode

Simulation Mode Simulation Mode > 2%

> 2%

> 0.25%

Failure Limit

Pass

Pass

Pass

Pass

Measurement  Measurement  > 0.50% Or not Measurement

# ofWarnings

0

0

0

0

0

0

# of Failures

0

0

0

0

0

0

# of Samples

11

Figure 5-6  Capture Log Example

Special Notes for the Data Capture file:

1. The FS200 utility capture file will only contain fields pertinent to the installation. For

example, a Dual Path system with only Path-1 enabled will not present any data columns

FS2

0

0 Programming Manual, 03/2020,

 

A5E02951525-AB

Summary of Contents for SITRANS F FS200 Utility





































Reviews:

No comments