Siemens SITOP PSU3800 12 V/20 A User Manual Download Page 51

Page: 51 / 108

Installation

5.2 Output-side connection

SITOP PSU8200/3800 3ph
Manual, 05.2018, C98130-A7638-A1-6-7629

5.2

Output-side connection

The SITOP PSU8200/3800 3ph power supply provides at its output an isolated (= non-

grounded) SELV output voltage (Safety Extra Low Voltage). The output of the power supply

is no-load, overload and short-circuit proof. If an overload occurs, the electronic current

limiting function limits the output current to a maximum value (see Section Technical data

(Page 53)).

Figure 5-2

Output connection

The output voltage is connected via the "+" and "–" terminals at the output of the power

supply (see Figure Output connection (Page 51)). Ensure that the output cables are

dimensioned correctly for the maximum output current rms value and fused accordingly.

Note
If the safety concept of the plant or system specifies that the DC output circuit should be

grounded ((PELV, Protected Extra Low Voltage), then it is permissible that the output voltage

of the SITOP power supply is grounded. In this case, ideally, the grounding at the output

should be directly connected from terminal "-" of the power supply to a suitable connection

point of the protective conductor system (PE) of the plant or system.

Summary of Contents for SITOP PSU3800 12 V/20 A













































































































Search results

Summary of Contents for SITOP PSU3800 12 V/20 A

Reviews:

Related manuals for SITOP PSU3800 12 V/20 A

Brands by name

Popular brands

Siemens SITOP PSU3800 12 V/20 A, User Manual

Search results

Summary of Contents for SITOP PSU3800 12 V/20 A

Reviews:

Related manuals for SITOP PSU3800 12 V/20 A

Brands by name

Popular brands