Siemens SITOP PSU3800 12 V/20 A User Manual Download Page 19

Page: 19 / 108

Description, device design, dimension drawing

2.5 Change-over switch

SITOP PSU8200/3800 3ph
Manual, 05.2018, C98130-A7638-A1-6-7629

For 6EP3437-8UB00-0AY0 (24 V/40 A)

Switch

OFF

influences the output

characteristic in the

load range

Parallel operation:

"Soft" characteristic curve (see Figure 6-20 Output

characteristic 6EP3437-8UB00-0AY0 parallel opera-

tion (B OFF) (Page 67)) for the parallel operation of

two or more devices: The output voltage falls with

increasing output current.

This means that for full output current the highest

output voltage can normally no longer be attained.

Single operation:

delivery condition

"Hard" characteristic curve (see Figure 6-

11 Output characteristic 6EP3437-

8UB00-0AY0 single operation (B OFF)

(Page 64)) for normal operation (single

operation): The output voltage is inde-

pendent of the output current.

is used to switch over

the output current

Rated current:

out rated

= 30 A, no latching shutdown

see Figure 6-29 Output characteristic 6EP3437-

8UB00-0AY0 single operation (Page 70)

Rated current:

delivery condition

out rated

= 40 A, no latching shutdown

Note
Selector switches may only be activated when the device is switched off.

Summary of Contents for SITOP PSU3800 12 V/20 A













































































































Search results

Summary of Contents for SITOP PSU3800 12 V/20 A

Reviews:

Related manuals for SITOP PSU3800 12 V/20 A

Brands by name

Popular brands

Siemens SITOP PSU3800 12 V/20 A, User Manual

Search results

Summary of Contents for SITOP PSU3800 12 V/20 A

Reviews:

Related manuals for SITOP PSU3800 12 V/20 A

Brands by name

Popular brands