Siemens SIREMOBIL Iso-C 3D Installation Instructions Manual Download Page 52

Page: 52 / 98

SIREMOBIL Iso-C 3D

SPR2-230.814.01

Page 2 of 42

Siemens AG

Rev. 05

08.04

CS PS 24

Medical Solutions

6 - 2

3. Part of activities independent of serial number

Replacing the monitor

SIMOMED HM

•

Remove the monitor on the right as follows.

•

Remove the monitor cover (Fig. 3).

•

Remove the shielding plate (Fig. 4).

•

Remove the connection housing, if in place (Fig. 5).

•

Remove all cables from the monitor to be replaced.

•

Reattach all previously removed parts to the monitor.

•

Remove the 2 screws at the monitor mounting (Fig. 6).

•

Lift down the monitor.

If the TFT displays were ordered and delivered, disregard this
section. Continue with the section "Replacing the monitor, TFT
displays".

Fig. 3

Monitor cover

Fig. 4

Shielding plate

Fig. 5

Connection housing

Fig. 6

Monitor attachment

NOTE

Markierung für Tastaturschublade

Summary of Contents for SIREMOBIL Iso-C 3D



































































































Search results

Summary of Contents for SIREMOBIL Iso-C 3D

Reviews:

Siemens SIREMOBIL Iso-C 3D, Installation Instructions Manual, Page: 52 / 98

Search results

Summary of Contents for SIREMOBIL Iso-C 3D

Reviews: