manualshive.com logo in svg

Siemens SIREMOBIL Iso-C 3D, Installation Instructions Manual, Page: 11 / 98

Share
Download
Siemens SIREMOBIL Iso-C 3D Installation Instructions Manual Download Page 11

General

1 - 5

Siemens AG

 

SPR2-230.814.01

Page 5 of 6

SIREMOBIL Iso-C 3D

Medical Solutions

Rev. 05

08.04

CS PS 24

 

 

Check list prior to installing the 3D option

1

Actions required prior to installing the 3D option 

1

Check the serial number 

..................

For serial numbers up to 

1408

, a specially trained 

CSE is required for installing the option (refer to the 
Field Service Strategy).

For serial numbers beginning with 

1409

the option may be installed by a CSE trained in 
SIREMOBIL Iso-C 3D. 

A room suitable for the installation is available. 

The tools to be provided by the R.U. are available. 

All auxiliary service tools to be provided by the R.U. 
are available.

Function check of the SIREMOBIL Iso-C in accor-
dance with the operating manual

Testing as part of the IQ quick test: 
- Chapter "checking the ADR characteristics" 
- Chapter "resolution" 
- Chapter "image interferences" 

Summary of Contents for SIREMOBIL Iso-C 3D



































































































Reviews:

No comments