Siemens SIMOTION TM15 Commissioning Manual Download Page 73

Page: 73 / 99

Technical data

6.1 Operating modes

TM15 / TM17 High Feature Operating Manual
Commissioning Manual, 05/2009

Level-triggered enable

With a level-triggered enable, output cams are only output to the output if the enable signal is

applied statically before the output cam start.
If the enable signal is retracted before the output cam end, the output cam is still output up to

the end. New output cams are no longer output.

(QDEOHLQSXW

RSWLRQ70RQO\

2XWSXWRIRXWSXWFDP

7HUPLQDWH

RXWSXWRI

RXWSXW

FDPV

1RW

HQDEOHG

Figure 6-2

Diagram – Output of output cam with level-triggered enable signal

Table 6- 3

Timing of output of output cam

Timer

TM15

TM17 High Feature Comments

125 µs

1 µs

Resolution

≥ 125 µs

≥ 50 µs (typical)
≥ 100 µs (maximum)

Depends on the load conditions of the

output. See "Supplementary SINAMICS

System Components for SIMOTION"

Manual.

≥ 125 µs

(typical)

≥ 150 µs

(maximum)

≥ 75 µs (typical)
≥ 250 µs (maximum)

Depends on the load conditions of the

output. See "Supplementary SINAMICS

System Components for SIMOTION"

Manual.

IPO or servo

Depends on the technology object cycle

time.

Not applicable

(TM15 does not

have an enable

function)

≥ 1 µs/125 µs

Depends on selected
filter times. See "Supplementary

SINAMICS System Components for

SIMOTION" Manual.

Times specified for positive logic.
IPO = Interpolator cycle clock

DRIVE CLiQ cycle clock, but at least 125 µs

Summary of Contents for SIMOTION TM15




































































































Search results

Summary of Contents for SIMOTION TM15

Reviews:

Siemens SIMOTION TM15, Commissioning Manual, Page: 73 / 99

Search results

Summary of Contents for SIMOTION TM15

Reviews: