manualshive.com logo in svg

Siemens SIMOTION TM15, Commissioning Manual

Share
Download
Siemens SIMOTION TM15 Commissioning Manual Download Page 65

 

Application tips 

 

5.5 Other application examples 

TM15 / TM17 High Feature Operating Manual 
Commissioning Manual, 05/2009 

65

 

5.5.5

 

Multiple µs-granular measuring ranges 

A maximum of one measuring range can be specified for the Measuring Input technology 

object. Only measurements taken within this range are recorded. 
The resolution of the measuring range of the Measuring Input technology object conforms to 

the measuring input processing cycle clock (IPO interpolator cycle clock, IPO2 interpolator 

cycle clock, or position control cycle clock). 
If more than one measuring range is needed or if the measuring range is to be specified 

more precisely, this can be accomplished in the application as described below: 
●

 

Configure a Measuring Input technology object with level-triggered enable on the TM17 

High Feature (measuring input e.g., DI/O 0; assigned enable input is therefore DI/O 10) 

●

 

Configure an output cam track, and output this to an output of an output cam of TM17 

High Feature. (Output of output cam e.g., to DI/O 12) 

●

 

Connect the output of the output cam to the enable input of the measuring input 

The output cam track is used to define the measuring range for the measuring input in the 

application (each output cam corresponds to one measuring range and can therefore be 

specified on a µs-specific basis). 

Summary of Contents for SIMOTION TM15




































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands